Nordson Encore LT Product Manual Download

Page: 45 / 92

Operation

4-11

Part 1604857-04

2014 Nordson Corporation

Changing Conical Nozzles and Deflectors

WARNING:

Release the spray gun trigger, put the controller to sleep, and

ground the electrode before performing this procedure. Failure to observe

this warning could result in a severe electrical shock.

NOTE:

The electrode assembly shipped with the gun is fitted with a

tapered electrode holder that will not accept a conical deflector and must be

changed prior to using the conical nozzle and deflector. Follow the

instructions in the conical nozzle kit shipped with the gun for this conversion.
1. Purge the spray gun and press the Enable/Disable button to put the

controller to sleep in order to prevent accidental gun triggering.

2. See Figure 4-8. Gently pull the deflector off the electrode assembly. If

only changing the deflector, install the new one on the electrode

assembly, being careful not to bend the electrode wire.

3. To change the entire nozzle, unscrew the nozzle nut counterclockwise.
4. Pull the conical nozzle off the electrode assembly.

NOTE:

Re-install the electrode assembly if it comes out of the powder

outlet tube.
5. Install a new conical nozzle on the electrode assembly. The nozzle is

keyed to the electrode assembly.

6. Screw the nozzle nut onto the gun body clockwise until finger-tight.
7. Install a new deflector on the electrode assembly. Do not bend the

electrode wire.

8. Press the Enable/Disable button to wake up the controller.

NOTE:

To clean nozzles, use the

Recommended Cleaning Procedure for

Powder Contact Parts

on page 4-13.

Deflector

Nozzle Nut

Nozzle

Conical Electrode Holder

Electrode

Assembly

Figure 4-8

Changing a Conical Nozzle

Summary of Contents for Encore LT





























































































Search results

Summary of Contents for Encore LT

Reviews:

Related manuals for Encore LT

Brands by name

Popular brands

Nordson Encore LT, Product Manual

Search results

Summary of Contents for Encore LT

Reviews:

Related manuals for Encore LT

Brands by name

Popular brands