65E Turbo Motor Grader
Service Manual
Service 1.00_2006.03
Section 7
Hydraulics
7-89
Cylinder Disassembly
The hydraulic cylinders are basically the same design,
except that the wheel lean, moldboard shift, circle side
shift, lift, articulation, front end attachment, and rear rip-
per cylinders use a threaded cap to retain the gland.
The steering and moldboard pitch cylinders use an
internal snap ring to retain the gland. The bank slope
cylinder uses a threaded cylinder head in place of a cap
and gland that screws into the tube assembly, and a
snap ring to retain the piston.
Cylinder seal kits provide parts (seals, o-rings, etc.)
most likely to need replacement when rebuilding the
cylinders. Refer to the Parts Catalog for hydraulic cylin-
der Seal Kit Part Numbers.
Before disassembly, remove cylinders in accordance
with previous Cylinder Removal procedures.
NOTE:
The cap can be loosened before cylinder is
removed.
Step 1:
Turn cap, 1, clockwise using a pipe wrench on
the threaded cap. Use a snap ring pliers to remove
internal snap ring as appropriate.
Step 2:
Pull rod, 1, out of barrel, removing gland, 2, with
the rod and piston, 3.
Step 3:
Clamp rod, 1, at clevis end in a vice, taking care
not to damage chrome plating. Remove nut, 4, on end
of rod.
Step 4:
Remove piston, 3, and gland, 2, from rod, 1.
Summary of Contents for 65E Turbo
