18
N70-2 GT
INSTRUCTIONS FOR USE
The N70-2 GT helmet can be used in six different con
fi
gurations. As a matter of fact, It
features a visor and removable protective chin guard which can be assembled on the
product jointly, separately or be removed from the latter. Besides these elements, it also
comes with a peak (provided, depending on the product versions, in the box or as an
accessory/spare part) which can be assembled to replace the visor (Fig.1).
Using the helmet in the con
fi
guration - with chin guard fastened and visor pulled down
- obviously offers the highest level of protection as compared to other con
fi
gurations.
The covers of the chin guard fastening slots (which
must
be
fi
xed should the helmet
be used without the chin guard) and the side plates (which
must
be
fi
xed should the
helmet be used without the visor and without the peak) are provided in the box.
REMOVABLE PROTECTIVE CHIN GUARD
1
RELEASING THE REMOVABLE PROTECTIVE CHIN GUARD
1.1 Open the visor completely.
1.2 Push the right and left chin guard release levers downwards and simultaneously
remove the chin guard from the helmet by pulling it outwards (Fig.2).
Warning:
whenever you wish to release the chin guard to use your helmet in the
jet con
fi
guration, insert the right and left chin guard locking slot covers (chin guard
covers) into the respective slots on the right and left side frames and push them
towards the inside of the helmet until you hear a fastening click (Fig.3).
The right and left chin guard covers are different from each other and they are
marked at their rear part as “R” (right) and “L” (left).
2
FASTENING THE REMOVABLE PROTECTIVE CHIN GUARD
Before fastening the chin guard to the helmet, remove the chin guard covers by per-
forming the following operations:
2.1 Open the visor completely.
2.2 Remove the right and left chin guard covers by pulling them outwards (Fig.3).
2.3 Insert the right and left chin guard ends simultaneously into the slots on the cor-
responding side frames of the helmet and press the chin guard towards the inside
of the helmet until you hear the fastening click on both sides (Fig.4).
2.4 Make sure the chin guard is correctly fastened at both ends by gently pulling it
towards the outside of the helmet.
WARNING
-
Never remove or disassemble the semi-rigid inner padding of the protective chin
guard.
-
When the helmet is used without the removable protective chin guard, always
assemble the chin guard covers supplied.
-
If in doubt on how the manual chin guard release device works, please contact a
Nolangroup authorized dealer.
VISOR (NJS-07S / NJS-07L)
The visor comes in two sizes, depending on the size of the shell:
-
Small (for sizes XXS to M)
-
Large (for sizes L to XXXL)
Should you buy the visor as an accessory/spare part, we kindly request you to check
the correct size of the visor from a Nolangroup authorised dealer.
1
DISASSEMBLING THE VISOR
1.1 Open the visor completely (Fig.5).
1.2 Push the release lever of the left side mechanism completely upwards (Fig.6) and
then push the visor away from the helmet (Fig.7).
1.3 Disengage the release lever so that it returns downwards, to its initial position.
1.4 Follow the previous operations on the right side of the helmet.
2
ASSEMBLING THE VISOR
2.1 Place the left side of the visor on the corresponding side mechanism centring the
side hole of the visor on the mechanism (Fig.8).
2.2 Push the release lever of the mechanism completely upwards and, subsequently,
push the visor against the mechanism (Fig.6,7).
2.3 Disengage the release lever so that it returns downwards, to its initial position.
Then ensure that the visor remains engaged to the mechanism by pulling it out-
wards.
2.4 Follow the previous operations on the right side of the helmet.
2.5 Close the visor completely.
WARNING
-
Make sure that the mechanisms are working properly. Open and close the visor,
making sure that the mechanisms hold it in the different positions. If necessary,
repeat the above-mentioned operations.
-
Do not use the helmet if the visor has not been assembled properly.
-
Do not remove the side mechanisms from the shell.
-
Should any of the side mechanisms fail or be damaged, please contact a Nolan-
group authorized dealer.
SIDE INSERTS OF THE VISOR AND VISOR AIR INTAKE
The visor features the presence of side inserts and an air intake which can be removed
from the latter to facilitate normal maintenance and cleaning operations.
1
DISASSEMBLING THE SIDE INSERTS OF THE VISOR AND VISOR AIR INTAKE
1.1 Remove the visor from the helmet (see instructions above).
1.2 Release the left side insert from the visor by pushing outwards at the three en-
gagement elastic click-on positions (Fig.9). Repeat the same operation on the right
side of the helmet.
1.3 Remove the visor air intake by
fi
rst releasing the internal air diffuser “A” and then
removing the intake external part “B” from the hole provided in the visor(Fig.10).
2
ASSEMBLING THE SIDE INSERTS OF THE VISOR AND VISOR AIR INTAKE
2.1 Engage the left-hand side insert to the visor by pushing inwards at the three en-
gagement elastic click-on positions (Fig.9). Repeat the same operation on the right
side of the helmet.
Summary of Contents for N70-2 GT
