Nokia 500i Installation Manual Download Page 68

Page: 68 / 80

Troubleshooting

Nokia 500i Installation Guide

Problem

Not connected with a null-modem cable.

Solution

Verify that you are using a null-modem cable.

Problem

Wrong terminal settings.

Solution

Verify terminal settings: 9600 bps, 8 data bits, 1 stop bit, no

parity.

Problem

Defective gateway or file system.

Solution

Contact the Nokia customer support site listed in

“Nokia Contact

Information”

on page 3.

Do Not Get a Login Prompt—Error Messages Appear

Problem

The gateway is defective, or the file system on the gateway is

defective.

Solution

Contact the Nokia customer support site listed in

“Nokia Contact

Information”

on page 3.

Do Not See Interfaces that Should be Present

Problem

Local gateway ports do not appear.

Solution

Your network interface card (NIC) might be defective. Contact

the appropriate Nokia customer support site as listed in

“Nokia Contact

Information”

on page 3.

Summary of Contents for 500i

















































































Search results

Summary of Contents for 500i

Reviews:

Brands by name

Popular brands

Nokia 500i, Installation Manual

Search results

Summary of Contents for 500i

Reviews:

Brands by name

Popular brands