Nokia 500i Installation Manual Download Page 61

Page: 61 / 80

Installing a Network Interface Card

Nokia 500i Installation Guide

You can configure the Ethernet interfaces with Nokia VPN Manager. See the
Nokia IP VPN Gateway Configuration Guide.

Front Panel Details

Figure 9

shows the front panel details for the four-port Nokia 10/100 Ethernet

NIC that you use in the Nokia 500i gateways.

Figure 9 PMC Four-port 10/100 Ethernet NIC

For connectors and cable information for the four-port 10/100 Ethernet NIC,
see

“Ethernet Cables”

on page 39.

Caution

Cables that connect to the Ethernet NIC must be IEEE 802.3
compliant to prevent potential data loss.

Fiber Optic or Copper Gigabit Ethernet NIC

This section provides information about the PMC fiber optic or copper
Gigabit Ethernet network interface cards (NICs), which you can use with the
Nokia 500i gateways.

Link LEDs (steady green)
Activity LEDs (blinking green)

Ports

Summary of Contents for 500i

















































































Search results

Summary of Contents for 500i

Reviews:

Brands by name

Popular brands

Nokia 500i, Installation Manual

Search results

Summary of Contents for 500i

Reviews:

Brands by name

Popular brands