manualshive.com logo in svg

Nokia 500i, Installation Manual

Share
Download
Nokia 500i Installation Manual Download Page 44

3

  Installing and Replacing Optional Cards

44

 

Nokia 500i Installation Guide

Caution

Protect your gateways and other electronic equipment from 
electrostatic discharge damage by making sure you are properly 
grounded before you touch any component.

Caution

When you handle a NIC, take care not to damage the EMI shield on 
the top edge of the faceplate.

Installing Flash Memory PC Cards

This section provides information about how to install or replace additional 
nonvolatile random access memory in your gateway by using a flash memory 
flash card.

You can order flash memory cards separately for the Nokia 500i gateway. 
Each of these gateways has two PC-card slots that each support a flash 
memory card as small as 8 MB and as large as 64 MB. The slots, also known 
as PCMCIA slots, permit hot swapping. The two slots are located on the front 
panel.

Flash memory cards provide the following:

!

Data storage

!

Backup and storage of operating system and applications

!

Initial gateway configuration

!

Operating system booting

The default boot order is:

1.

External flash memory (PC card)

2.

Internal flash memory

Summary of Contents for 500i

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands