Nokia 500i Installation Manual Download Page 62

Page: 62 / 80

Installing and Replacing Optional Cards

Nokia 500i Installation Guide

Note
NICs in the 6U PMC carrier on the Nokia 500i are not hot swappable. You
must turn off power to the system before replacing NICs on the Nokia
500i gateway.

The fiber optic Gigabit Ethernet NICs provide the following features:

High bandwidth

Full-duplex mode operation up to 1 Gbps (no half-duplex support)

Link speed autoadvertising

Compliance with IEEE 802.3z Gigabit Ethernet specification

You can configure and manage Ethernet interfaces with Nokia VPN Manager
software. See the Nokia IP VPN Gateway Configuration Guide.

Front Panel Details

Figure 10

shows the front panel details for the dual-port fiber optic Gigabit

Ethernet NIC you use in the Nokia 500i gateway.

Figure 10 PMC Dual-Port Fiber Optic Gigabit Ethernet NIC

Figure 11

shows the front panel details for the dual-port copper Gigabit

Ethernet NIC.

00239b

GIGE

Port 1 (P1)

Port 2 (P2)

Link LED (green)

Activity LED (yellow)

Summary of Contents for 500i

















































































Search results

Summary of Contents for 500i

Reviews:

Brands by name

Popular brands

Nokia 500i, Installation Manual

Search results

Summary of Contents for 500i

Reviews:

Brands by name

Popular brands