manualshive.com logo in svg

Nokia 500i, Installation Manual

Share
Download
Nokia 500i Installation Manual Download Page 46

3

  Installing and Replacing Optional Cards

46

 

Nokia 500i Installation Guide

Installing an Encryption Accelerator Card

This section describes how to replace the Nokia Encryption Accelerator Card. 
The card is included with the Nokia 500i gateways and installed before the 
gateway is delivered to you. These instructions apply only if you are replacing 
the card.

The Nokia Encryption Accelerator Card provides high-speed cryptographic 
processing that enhances the performance of VPN tunnels. By taking over 
cryptographic processing, the card allows the gateway CPU to perform other 
tasks.

The Nokia Encryption Accelerator Card is in a PMC format for the Nokia 
500i. This card has no external cable connection ports and requires no cables.

The following security algorithms are supported:

!

MD5 and SHA-1 authentication

!

DES and 3DES encryption

!

128-bit, 192-bit, and 256-bit AES encryption

To install the accelerator card

1.

Turn off the power switch on the rear of the gateway and unplug the 
power cord.

Note
If you cannot access the power switch, you can still perform this 
procedure. When the slide tray assembly is removed from the chassis 
assembly, power to a Nokia 500i is automatically disconnected.

Summary of Contents for 500i

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands