manualshive.com logo in svg

Nintendo Ultra64, Programmer'S Manual

Introducing the Nintendo Ultra64 Programmer's Manual. Unlock the potential of this iconic gaming console with our thorough and comprehensive manual. Download it for free from manualshive.com and delve into the intricacies of programming this revolutionary device, seizing the opportunity to create unforgettable gaming experiences.

Share
Download
background image

Revision 1.0

191

Format: 

lsv vt[element], offset(base)

Description: 

This instruction loads a short (16 bits) from the effective address of DMEM into vector register 

vt

 

starting at byte 

e

.

The effective address is computed by shifting the 

offset

 up by 1 bit and adding it to the contents of 

the 

base

 register (a SU GPR).

The 

offset

 field of the instruction is encoded by shifting the offset used in the source code down 1 

bit, so the offset used in the source code must be a multiple of 2 bytes.

This instruction has three load delay slots (results are available in the fourth instruction following 
this load). If an attempt is made to use the target register 

vt

 in a delay slot, hardware register 

interlocking will stall the processor until the load is completed.

Note:  

The element specifier 

element

 is the byte element of the vector register, not the 

ordinal element count, as in VU computational instructions.

Operation:

Exceptions: 

None   

LSV

into Vector Register

Load Short

31

26

20

21

15

16

0

LWC2

base

vt

6

5

5

1 1 0 0 1 0

LSV

4

5

element

6

10

7

11

7

LSV

0 0 0 0 1

25

offset

T:

Addr



 ((offset

15

)

15

 || offset

15...0

 || 0

1

) + GPR[base]

VR[vt][element]

15...0

 

 dmem[Addr

11...0

]

15...0

Summary of Contents for Ultra64












































































































































































































































































































































Reviews:

No comments

Related manuals for Ultra64

TC Electronic M300 Service Manual preview
M300
Brand: TC Electronic Pages: 2
SAF Phoenix G2 IDU Quick Start Manual preview
Phoenix G2 IDU
Brand: SAF Pages: 30
Dialogic EDP-10 Quick Install Manual preview
EDP-10
Brand: Dialogic Pages: 2
RAK RAK3372 Quick Start Manual preview
RAK3372
Brand: RAK Pages: 30
Acces I/O products MPCIE-ICM232-2 Hardware Manual preview
MPCIE-ICM232-2
Brand: Acces I/O products Pages: 5
Enertronica Santerno SINUS H PROFInet User Manual preview
SINUS H PROFInet
Brand: Enertronica Santerno Pages: 34
Danville Signal Processing dspstak 21262sx User Manual preview
dspstak 21262sx
Brand: Danville Signal Processing Pages: 35
Avenview DVI-PROWALL-9X Instruction Manual preview
DVI-PROWALL-9X
Brand: Avenview Pages: 28
ZoneVu ZSI-450-IP Installation Manual & User Manual preview
ZSI-450-IP
Brand: ZoneVu Pages: 15
FUNcube Dongle Pro User Manual preview
Dongle Pro
Brand: FUNcube Pages: 23
IBM 2078-4F4 Quick Installation Manual preview
2078-4F4
Brand: IBM Pages: 130
Xilinx MP3 NG Application Note preview
MP3 NG
Brand: Xilinx Pages: 27
Lattice Semiconductor LatticeMico GPIO Manual preview
LatticeMico GPIO
Brand: Lattice Semiconductor Pages: 28
IFM QHA200 Instructions For Setup preview
QHA200
Brand: IFM Pages: 12
Radica Games DAVID-II 716 Operating And Maintenance Instruction Manual preview
DAVID-II 716
Brand: Radica Games Pages: 40
Airvana ipBTS C30 Installation And Commissioning Manual preview
ipBTS C30
Brand: Airvana Pages: 90
Renesas HD74HCT1G04 Datasheet preview
HD74HCT1G04
Brand: Renesas Pages: 8
Buffalo AirStation G54 WLA2-G54 Quick Setup Manual preview
AirStation G54 WLA2-G54
Brand: Buffalo Pages: 8

Brands by name

Popular brands

Load more brands