Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF) Repair Manual Download

Page: 55 / 93

JAA80151-R.3718.A

- Ａ 28・AF-S 1-2/2.8G -

April��2��8

��2��8

�2��8

2��8

Convex portion

Cutout

Connect the zoom-FPC to the connector of the main PCB.

Tuck the slackened part of the FPC inwards.

�

Zoom-FPC

Zoom ring

Fit the cutout of the exterior fixed tube unit with the convex portion of the zoom ring, then mount

the zoom ring.

�

Grease: GN-20S

Apply to the sliding
surface.

Bottom

Grease: PL-22SEL

Apply to 3 places of sliding
surface.

Caution: Connect the FPCs straightforward

so that they are all the way seated.

Changed page

△× 2

Grease Oil barrier: OS-30MF

△ (Revision)

Grease Oil barrier: OS-30MF

△ (Revision)

INC

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)






























































































Search results

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Reviews:

Related manuals for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Brands by name

Popular brands

Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF), Repair Manual

Search results

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Reviews:

Related manuals for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Brands by name

Popular brands