Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF) Repair Manual Download

Page: 41 / 93

JAA80151-R.3718.A

- Ａ 4・AF-S 4-24/2.8G -

Focus turning-tube

Roller pin

Focus turning-tube

Inner fixed tube

"A" section

Screw hole

Caution:

Avoid touching of fingers or of the screwdriver on the surface of magnetic tape.

Align the "A" section of the focus turning-tube with the roller pin of the inner fixed tube, and mount

the focus turning-tube.
After mounting the focus turning-tube, peel off the protection tape.

�

Inner fixed tube

Focus turning-tube

#157×3

Attach three roller units (#158 and #157) in the numeric order from 1 to 3.

�

Magnetic tape

#158×3

Adhesive: Lockend B

Protection tape

INC

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)






























































































Search results

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Reviews:

Related manuals for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Brands by name

Popular brands

Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF), Repair Manual

Search results

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Reviews:

Related manuals for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Brands by name

Popular brands