Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF) Repair Manual Download

Page: 84 / 93

JAA80151-R.3718.A

- Ａ・AF-S 4-24/2.8G -

300mm

45mm

（+100μm）

（‑100μm）

（‑50μm）

（0μm）

（+50μm）

Aberration compensation data writing adjustment

・

This adjustment uses the software which calculates the aberration compensation data according to the

feature of lens aberration and writes in FLASH-ROM of the lens, in order to improve the accuracy of
autofocus.

Note: This adjustment is necessary when the main PCB and/or each lens part (glass, lens chamber)

is replaced and/or when each lens part is disassembled. Be sure to make this adjustment after
completing inspecting and adjusting the main PCB.

(1) Preparation

　　・

Test chart (Self-made tool: ref. Procedure for how to create it.)

　　・

Tripod

　　・

Camera

（

D100 or D200

）

　　・

Personal computer

　　・

USB cable

（

UC-E4

）

　　・

Adjustment software (

LWM

.exe

�

used for the lens optical alignment.)

(2) Procedure for how to create Test chart

　　・

Photocopy the next page and cut out 1 target chart and 5 resolution charts.

（

Target chart

）

（

Resolution chart

）

　　・

As shown below, put each chart in position at the specified spacings.

Note: Only in the center, put the target chart on the central resolution chart.

INC

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)






























































































Search results

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Reviews:

Related manuals for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Brands by name

Popular brands

Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF), Repair Manual

Search results

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Reviews:

Related manuals for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Brands by name

Popular brands