manualshive.com logo in svg

Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF), Repair Manual

The Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF) is a professional-grade lens renowned for its exceptional image quality and versatility. To ensure that users have all the necessary information, a comprehensive Repair Manual and user manual are available for download, absolutely free, from our website manualshive.com.

Share
Download
background image

JAA80151-R.3718.A

- Ａ �・AF-S 1-2/2.8G -

April����2��8

����2��8

��2��8

�2��8

2��8

#80

#87

#93

Full tightening of 1st lens-G lead key

1st lens-G lead ring

1st lens-G key×3

Attach three rollers to the cam tube.

�

Roller

#191×6

By rotating the cam tube, check operations of zooming.
If the zooming is not smooth, adjust the attaching position of the 1st lens-G key. 

At the position where the zooming becomes smooth, tighten the three 1st lens-G keys fully with 
six screws (#191).

�

�

�

 Adhesive: Lockend R B

Be careful of the facing direction 

of #87 when assembled

Caution: Large backlash of the 1st lens-G lead ring may affect the accuracy of resolution.

△ (Revision)

Changed page 

△× 2

 Adhesive: Lockend R B

△ (Revision)

INC

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)






























































































Reviews:

No comments

Related manuals for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

VOIGTLANDER SUPER WIDE-HELIAR 15mm F4.5 Aspherical III Instruction Manual preview
SUPER WIDE-HELIAR 15mm F4.5 Aspherical III
Brand: VOIGTLANDER Pages: 9
Bausch & Lomb PuerVision2 Quick Start Manual preview
PuerVision2
Brand: Bausch & Lomb Pages: 16
Bausch & Lomb Boston EO Instructions For Use Manual preview
Boston EO
Brand: Bausch & Lomb Pages: 30
Barco QVD (7:1) Installation Manual preview
QVD (7:1)
Brand: Barco Pages: 11

Brands by name

Popular brands

Load more brands