Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF) Repair Manual Download Page 47

Page: 47 / 93

JAA80151-R.3718.A

- Ａ 20・AF-S 4-24/2.8G -

GMR unit

Caution:

Do NOT touch the sensor area directly

with hands.

Back side

#119×2

GMR sensor

GMR base plate

Boss×2

Boss hole×2

Fit the bosses of the GMR base plate in the boss-holes of the GMR sensor.
Tighten two screws (#119) in numeric order from

①

②

�

①

②

GMR base plate

Based on the following reference position, attach the tape (#190) to the GMR base plate, and peel
off a backing paper of the tape.

�

Reference position

#190
TA-0004 (3×10)

Based on the following reference position, attach the tape (#190) to the GMR base plate.

�

Reference position

#190
TA-0004 (3×10)

GMR base plate

INC

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)






























































































Search results

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Reviews:

Related manuals for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Brands by name

Popular brands

Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF), Repair Manual

Search results

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Reviews:

Related manuals for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Brands by name

Popular brands