Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF) Repair Manual Download Page 52

Page: 52 / 93

JAA80151-R.3718.A

- Ａ 2・AF-S 4-24/2.8G -

GMR unit

Tape (#196)

TA-0017(3×8)

×8)

Based on the reference position, fix the GMR-FPC with the tape (#196).

Attach [#196] so that its upper part protrudes from the edge of the GMR base plate by 1mm as

below. Then push [#196] from above with the fingers.

�

Connect the GMR-FPCs to the connectors of the main PCB.

�

Position the GMR-FPC towards the direction of the arrow.
Attach [#196] so that part of it protrudes from the edge of the GMR base plate by 1mm as below.

Then push [#196] from above with the fingers.

�

Caution: Do NOT attach [#196] at the closer position to the GMR sensor than [#190].

Caution: Connect the FPCs straight-

forward so that they are all

the way seated.

Adhesive: Screw lock

Connect the GMR-FPCs to the
connector, and lock them.

Lock

GMR base plate

1-mm protrusion from the edge
of the GMR base plate.

Tape (#190)

Tape(#196)

TA-0017(3×8)

1-mm protrusion from the edge of the
GMR base plate.

Caution: The tape [#196] must NOT touch the below

area of the FPC.

INC

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)






























































































Search results

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Reviews:

Related manuals for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Brands by name

Popular brands

Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF), Repair Manual

Search results

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Reviews:

Related manuals for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Brands by name

Popular brands