Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF) Repair Manual Download

Page: 56 / 93

JAA80151-R.3718.A

- Ａ 29・AF-S 1-2/2.8G -

April��2��8

��2��8

�2��8

2��8

Set the cam tube to WIDE-end. Put the zoom coupling key in the groove and tighten two screws
(#61).

�

Rear fixed tube

Reference

Fit the reference pin in the reference pinhole, and mount

the rear fixed tube.
Tighten five screws (

#172#173

�

#61×2

Zoom coupling key

Adhesive: Lockend B

#172#173

×5

Adhesive: Lockend

Ｂ

Bottom

Apply to 4 places.

Grease: GN-20S

Apply to the sliding surface.

Reference pinhole

Caution: Do NOT apply the adhesive here.

Changed page

△× 3

Grease Oil barrier: OS-30MF

△ (Revision)

INC

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)






























































































Search results

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Reviews:

Related manuals for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Brands by name

Popular brands

Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF), Repair Manual

Search results

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Reviews:

Related manuals for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Brands by name

Popular brands