Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF) Repair Manual Download

Page: 34 / 93

JAA80151-R.3718.A

- Ａ・AF-S 4-24/2.8G -

#83

#90

Roller

Caution: Be careful NOT to widen the slot when the roller is screwed in.

Adhesive: Lockend B

2nd lens-G unit

Attach the roller unit (#83 and #90) to the 2nd lens-G unit.

�

Caution: The screw (#81) will be temporarily attached until the procedure of "Aperture

Lever

adjustment (on Page A31).

Attach the limit plate with two screws (#81).

�

Limit plate

#81×2

Blade actuating-plate lever

Grease: I-40

Apply to the contacting surface of Limit
plate and Blade actuating-plate lever

Be careful of the facing direction
of #90 when assembled

Limit plate

INC

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)






























































































Search results

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Reviews:

Related manuals for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Brands by name

Popular brands

Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF), Repair Manual

Search results

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Reviews:

Related manuals for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Brands by name

Popular brands