Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF) Repair Manual Download Page 33

Page: 33 / 93

JAA80151-R.3718.A

- Ａ・AF-S 4-24/2.8G -

2nd lens-G unit

Roller ×3

#86

#91

Inner fixed tube

Handle with care: Blade actuating-plate spring

Align "A" section of the inner fixed tube with "B" section of the 2nd lens-G unit, and assemble

them.

�

Grease: GN-20S

Apply to overall surface of the 2nd lens-G
sliding tube.

Adhesive: Lockend B

"A" section

"B" section

Set the cam tube to WIDE position, and attach three roller units (#86 and #91).

�

∞ Tool hole for positioning

(ref. Page A17)

Cam tube

Caution: Handle the blade actuating-plate spring of the 2nd lens-G unit with care,

because it is easily deformed.

INC

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)






























































































Search results

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Reviews:

Related manuals for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Brands by name

Popular brands

Nikon AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF), Repair Manual

Search results

Summary of Contents for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Reviews:

Related manuals for AF-S Zoom-Nikkor ED 14-24mm/F2.8G (IF)

Brands by name

Popular brands