manualshive.com logo in svg

NETGEAR GSM7328Sv2 - ProSafe 24+4 Gigabit Ethernet L3 Managed Stackable Switch, Cli Manual

Get ready to optimize your network performance with the NETGEAR GSM7328Sv2 - ProSafe 24+4 Gigabit Ethernet L3 Managed Stackable Switch. Find the ultimate user satisfaction by easily accessing the detailed Cli Manual, available for free download from our website. Unlock the full potential of your device today.

Share
Download
background image

Managed Switch CLI Manual, Release 8.0.3

Quality of Service (QoS) Commands

8-23

v1.0, July 2010

The 

<dscpval> 

value is specified as either an integer from 0 to 63, or symbolically through one 

of the following keywords: af11, af12, af13, af21, af22, af23, af31, af32, af33, af41, af42, af43, be, 
cs0, cs1, cs2, cs3, cs4, cs5, cs6, cs7, ef

.

mark ip-precedence

This command marks all packets for the associated traffic stream with the specified IP Precedence 
value. The IP Precedence value is an integer from 0 to 7.

police-simple

This command is used to establish the traffic policing style for the specified class. The simple form 
of the police command uses a single data rate and burst size, resulting in two outcomes: conform 
and violate. The conforming data rate is specified in kilobits-per-second (Kbps) and is an integer 
from 1 to 4294967295. The conforming burst size is specified in kilobytes (KB) and is an integer 
from 1 to 128. 

For each outcome, the only possible actions are drop, set-cos-transmit, set-dscp-transmit, set-prec-
transmit, or transmit. In this simple form of the police command, the conform action defaults to 
transmit and the violate action defaults to drop. 

For set-dscp-transmit, a 

<dscpval>

 

value is required and is specified as either an integer from 0 

to 63, or symbolically through one of the following keywords: af11, af12, af13, af21, af22, af23, 
af31, af32, af33, af41, af42, af43, be, cs0, cs1, cs2, cs3, cs4, cs5, cs6, cs7, ef. 

For set-prec-transmit, an IP Precedence value is required and is specified as an integer from 0-7.

Format

mark ip-dscp <dscpval>

Mode

Policy-Class-Map Config

Incompatibilities

Drop, Mark CoS, Mark IP Precedence, Police 

Note: 

This command may not be used on IPv6 classes. IPv6 does not have a precedence 

field.

Format

mark ip-precedence <0-7>

Mode

Policy-Class-Map Config

Incompatibilities

Drop, Mark CoS, Mark IP Precedence, Police 

Policy Type

In

Summary of Contents for GSM7328Sv2 - ProSafe 24+4 Gigabit Ethernet L3 Managed Stackable Switch





















































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GSM7328Sv2 - ProSafe 24+4 Gigabit Ethernet L3 Managed Stackable Switch

Paradyne FrameSaver 9120 Installation Instruction Supplement preview
FrameSaver 9120
Brand: Paradyne Pages: 2
Ubiquiti U5-24-500W Quick Start Manual preview
U5-24-500W
Brand: Ubiquiti Pages: 23
Radicom WiFiHU2S-a/c Preliminary Designer’S Manual preview
WiFiHU2S-a/c
Brand: Radicom Pages: 27
NETGEAR WGR614 - Wireless-G Router Wireless Reference Manual preview
WGR614 - Wireless-G Router Wireless
Brand: NETGEAR Pages: 116
Teletronics International TT 900 User Manual preview
TT 900
Brand: Teletronics International Pages: 57
Kaptia Klever Getting Started preview
Klever
Brand: Kaptia Pages: 14
National Instruments Monochrome Image Acquisition Device NI 1410 User Manual preview
Monochrome Image Acquisition Device NI 1410
Brand: National Instruments Pages: 34
ADTRAN 239 T1 HDSL4 Installation And Maintenance Manual preview
239 T1 HDSL4
Brand: ADTRAN Pages: 20
Ruckus Wireless SmartZone 3.2 Quick Setup Manual preview
SmartZone 3.2
Brand: Ruckus Wireless Pages: 4
Axis P1355-E User Manual preview
P1355-E
Brand: Axis Pages: 64
SHOWTEC LED Operator 4 Manual preview
LED Operator 4
Brand: SHOWTEC Pages: 15
DAPAudio Odin CL-4 Connect User Manual preview
Odin CL-4 Connect
Brand: DAPAudio Pages: 20
Hamlet HRDSL108W Quick Installation Manual preview
HRDSL108W
Brand: Hamlet Pages: 6
Proxim Stratum Installation And Maintenance Manual preview
Stratum
Brand: Proxim Pages: 89
Gigamon GigaVUE H Series Hardware Installation Manual preview
GigaVUE H Series
Brand: Gigamon Pages: 55
3Com Router 3000 Series Manual preview
Router 3000 Series
Brand: 3Com Pages: 37
Digi TransPort WR44 v2 Testing Manual preview
TransPort WR44 v2
Brand: Digi Pages: 32
Emerson dixell Quick Start Manual preview
dixell
Brand: Emerson Pages: 8

Brands by name

Popular brands

Load more brands