Neousys Technology Nuvo-5002E User Manual Download Page 32

Page: 32 / 128

Nuvo-5000 Series User’s Manual

- 32 -

2.4 Internal I/O Functions

In addition to I/O connectors on the front/back panel, Nuvo-5000 series provides other

features via its on-board connectors, such as SATA ports, mini-PCIe sockets, internal USB

ports and MezIO

interface. In this section, we’ll illustrate these internal I/O functions.

NOTE

For demonstration purposes, Nuvo-5000 series will be used in most illustrations.

2.4.1 DDR4 SODIMM Sockets

Nuvo-5000 series provides two 260-pin, SODIMM sockets for installing DDR4 memory

modules. It supports maximal 32GB capacity by installing two 16GB DDR4 2133 MHz

SODIMM modules. For information of installing DDR4 memory modules, please refer to

section 3.3 for details.

Summary of Contents for Nuvo-5002E

























































































































Search results

Summary of Contents for Nuvo-5002E

Reviews:

Related manuals for Nuvo-5002E

Brands by name

Popular brands

Neousys Technology Nuvo-5002E, User Manual

Search results

Summary of Contents for Nuvo-5002E

Reviews:

Related manuals for Nuvo-5002E

Brands by name

Popular brands