Neousys Technology Nuvo-5002E User Manual Download Page 26

Page: 26 / 128

Nuvo-5000 Series User’s Manual

- 26 -

2.2.8 VGA Connector

Nuvo-5000 series has multiple display outputs on its front panel for connecting different

displays according to your system configuration. VGA connector is the most popular way for

connecting a display. The VGA output on Nuvo-5000 series supports up to 1920 x 1200

resolution. By BIOS default and hardware implementation, the VGA output is always

enabled in any case.

Nuvo-5000 series supports tipple independent display outputs with any combination of VGA,

DVI/HDMI and DisplayPort. To support multiple display outputs and achieve best DVI/HDMI

output resolution in Windows, you need to install corresponding graphics driver. Please

refer to section 4.5 for information of driver installation.

Note

Please make sure your VGA cable includes SDA and SCL (DDC clock and data) signals for correct

communication with monitor to get resolution/timing information. A cable without SDA/SCL can

cause blank screen on your VGA monitor due to incorrect resolution/timing output.

Summary of Contents for Nuvo-5002E

























































































































Search results

Summary of Contents for Nuvo-5002E

Reviews:

Related manuals for Nuvo-5002E

Brands by name

Popular brands

Neousys Technology Nuvo-5002E, User Manual

Search results

Summary of Contents for Nuvo-5002E

Reviews:

Related manuals for Nuvo-5002E

Brands by name

Popular brands