Neousys Technology Nuvo-5002E User Manual Download Page 25

Page: 25 / 128

Nuvo-5000 Series User’s Manual

- 25 -

2.2.7 DVI/HDMI Connectors

Nuvo-5000 series has multiple display outputs on its front panel for connecting different

displays according to your system configuration. DVI/HDMI transmits graphics data in

digital format and therefore can deliver better image quality at high resolution. The

DVI/HDMI connector on the front panel can either output DVI signals or HDMI signal

depending on the display device connected. It supports up to 1920 x 1200 resolution. You

can use a DVI to HDMI cable to connect a HDMI display device.

Nuvo-5000 series supports tipple independent display outputs with any combination of VGA,

DVI/HDMI and DisplayPort. To support multiple display outputs and achieve best DVI/HDMI

output resolution in Windows, you need to install corresponding graphics driver. Please

refer to section 4.5 for information of driver installation.

Summary of Contents for Nuvo-5002E

























































































































Search results

Summary of Contents for Nuvo-5002E

Reviews:

Related manuals for Nuvo-5002E

Brands by name

Popular brands

Neousys Technology Nuvo-5002E, User Manual

Search results

Summary of Contents for Nuvo-5002E

Reviews:

Related manuals for Nuvo-5002E

Brands by name

Popular brands