Neousys Technology Nuvo-5002E User Manual Download Page 40

Page: 40 / 128

Nuvo-5000 Series User’s Manual

- 40 -

2.5 MezIO

Interface

MezIO

is an innovative interface designed for integrating application-oriented I/O

functions into an embedded system. It offers computer signals, power rails and control

signals via a high-speed connector. MezIO

is also mechanically reliable benefited from its

3-point mounted mezzanine structure. A MezIO

module can leverage these signals to

implement comprehensive I/O functions.

Nuvo-5000 series incorporates MezIO

interface and universal mechanical design to

accommodate Neousys’ standard MezIO

modules. For customers who want to develop

their own MezIO

module, Neousys provides MezIO

design documents on a NDA basis.

Please contact Neousys for further information.

2.5.1 Pin Definition of MezIO

Interface

MezIO

interface leverages FCI BERGSTAK® board-to-board connector to provide

interconnectivity of high-speed signals. The receptacle part on the PCBA is FCI

61082-063402LF while the plug part on the MezIO

module is FCI 61083-064402LF.

Please refer to the following table for signal definition of its 60-pos connector.

Summary of Contents for Nuvo-5002E

























































































































Search results

Summary of Contents for Nuvo-5002E

Reviews:

Related manuals for Nuvo-5002E

Brands by name

Popular brands

Neousys Technology Nuvo-5002E, User Manual

Search results

Summary of Contents for Nuvo-5002E

Reviews:

Related manuals for Nuvo-5002E

Brands by name

Popular brands