NEC Univerge SV8100 DT310 User Manual Download Page 47

Page: 47 / 78

To respond to a Voice Over alert tone to your

extension:

Note:

You can only respond if you have a

Voice Over

key.

1. Press the

Voice Over

key (Service Code 751:48).

Note:

The Voice Over key lights steadily (green) and
you can talk to the interrupting party.

To return to your original call:

1. Press the

Voice Over

key.

Note 1:

Your Voice Over key flashes red when you are
talking to your original call.

CO/PBX DIALING OPTIONS

Save Number Dialed

To save the outside number you just dialed (up to 24

digits).

Note:

Use this feature before hanging up.

1. Press the Save Number Dialed key (Service Code

751:30).

To redial a saved number:

1. Press an idle trunk line key.

Note:

This selects a specific trunk for the call.

2. Press the

Save Number Dialed

key (Service Code

751:30).

Note:

The stored number dials out.

-OR-

1. Press the

Speaker

key.

2. Dial

715

Note 1:

Save Number Dialed automatically selects a
trunk from the same group as your original
call.

Note 2:

The stored number dials out.

Memo Dial

To store a number while you are on a call:

1. While on a call, press the

Memo Dial

key (Service

Code 751:31).

2. Dial the number you want to store.

3. Press the

Memo Dial

key again and continue with

the conversation.

List Dir ICM Prog

PREVIEW SAVED NUMBER

Summary of Contents for Univerge SV8100 DT310















































































Search results

Summary of Contents for Univerge SV8100 DT310

Reviews:

Related manuals for Univerge SV8100 DT310

Brands by name

Popular brands

NEC Univerge SV8100 DT310, User Manual

Search results

Summary of Contents for Univerge SV8100 DT310

Reviews:

Related manuals for Univerge SV8100 DT310

Brands by name

Popular brands