NEC Univerge SV8100 DT310 User Manual Download Page 40

Page: 40 / 78

To dial a Station Speed Dialing number:

1. Press the

Speaker

key.

2. Dial

(default Service Code).

-OR-

Press the

Redial

key.

-OR-

Press the

System Speed Dialing

key (Service

Code 751:27).

Note:

To preselect, press a Line key in step 1
(instead of pressing Speaker).

3. Dial the Station Speed Dial buffer number (Default:

000~999).

The stored number dials out.

Note 1:

Initially (at default), there are 1000 System
Speed Dial buffers.

Note 2:

Unless you preselect, Trunk Group Routing
selects the trunk for the call. The system may
optionally select a specific Trunk Group for
the call.

Note 3:

If you have a DSS Console, you may be able to
press a DSS Console key to chain to a stored
number.

To dial a Group Speed Dialing number:

1. Press the

Speaker

key.

2. Dial

(default Service Code).

-OR-

Press the

Redial

key.

-OR-

Press the

Group Speed Dialing

key (Service Code

751:28).

Note:

To preselect, press a Line key in step 1
(instead of pressing Speaker).

3. Dial the Group Speed Dial buffer number ( none at

default).

Note 1:

Initially, there are no Group Speed Dial
buffers assigned.

Note 2:

Unless you preselect, Trunk Group Routing
selects the trunk for the call. The system may
optionally select a specific Trunk Group for
the call.

Note 3:

If you have a DSS Console, you may be able to
press a DSS Console key to chain to a stored
number.

92142622000 NEC

2-13 WED 5:28PM

Conf Rpt Save Trf

Summary of Contents for Univerge SV8100 DT310















































































Search results

Summary of Contents for Univerge SV8100 DT310

Reviews:

Brands by name

Popular brands

NEC Univerge SV8100 DT310, User Manual

Search results

Summary of Contents for Univerge SV8100 DT310

Reviews:

Brands by name

Popular brands