NEC Univerge SV8100 DT310 User Manual Download Page 54

Page: 54 / 78

-OR-

Press the

Call Forwarding Programmable

Function Key

(Service Code 751:10).

3. Dial

4. Press the

Speaker

key or hang up.

Note:

Your Call Forwarding Programmable
Function Key goes off.

Call Forwarding Busy/No Answer (B/NA)

To set Call Forward – Busy/No Answer at a forwarding

station:

1. Pick up the handset or press the

Speaker

key.

2. Dial the

Call Forward – Busy/No Answer Service

Code

(default: 744).

-OR-

Press the

Call Forwarding Programmable

Function Key

(Service Code 751:13).

3. Dial

(Set).

4. Dial the destination extension or off-premise

number.

5. Press the

Speaker

key or hang up.

To cancel Call Forward – Busy/No Answer at a

forwarding station:

1. Pick up the handset or press the

Speaker

key.

2. Dial the

Call Forward – Busy/No Answer Service

Code

(default: 744).

-OR-

Press the

Call Forwarding Programmable

Function Key

(Service Code 751:13).

3. Dial

(Cancel).

4. Press the

Speaker

key or hang up.

To set Call Forward – Both Ring at a forwarding station:

1. Pick up the handset or press the

Speaker

key.

2. Dial the

Call Forward – Both Ring Service Code

(default: 745).

-OR-

Press the

Call Forwarding Programmable

Function Key

(Service Code 751:14).

3. Dial

(Set).

4. Dial the destination extension number.

1:SET 0:CANCEL

CF-BNA

12345678

CF-BNA

Summary of Contents for Univerge SV8100 DT310















































































Search results

Summary of Contents for Univerge SV8100 DT310

Reviews:

Brands by name

Popular brands

NEC Univerge SV8100 DT310, User Manual

Search results

Summary of Contents for Univerge SV8100 DT310

Reviews:

Brands by name

Popular brands