NEC Univerge SV8100 DT310 User Manual Download Page 39

Page: 39 / 78

Trunk Queuing

After pressing a busy Line key and receiving the trunk
busy indication:

1. Dial

or press

Trunk Queuing/Camp On

key

(Service Code 751:35).

2. Replace the handset.

Note:

When a line is available, your telephone will
ring; lift the handset and place the call.

Last CO/PBX Number Redial

1. Without lifting the handset,

press the

Redial

key.

2. To redial the last number, press

-OR-

Search for the desired number from the Redial List by

pressing the

List Softkey

and then the

Redial

Softkey

3. Press the

Up Arrow/Down Arrow

VOLUME UP/

VOLUME DOWN

keys to search for the desired

number.

4. Lift the handset or press

Speaker

to place the call.

Speed Dial – System/Group/Station

To dial a Station Speed Dial number:

1. Press the

Speaker

key.

2. Dial

(default Service Code).

Note:

To preselect, press a Line key in step 1
(instead of Speaker).

3. Dial the Station Speed Dial buffer number (0~9):

1 = Station Speed Dial buffer 1

2 = Station Speed Dial buffer 2

0 = Station Speed Dial buffer 10

Note 1:

The stored number dials out.

Note 2:

Unless you preselect, Trunk Group Routing
selects the trunk for the call. The system may
optionally select a specific Trunk Group for
the call.

Note 3:

If you have a DSS Console, you may be able to
press a DSS Console key to chain to a stored
number.

Redial CID

LIST MENU

Summary of Contents for Univerge SV8100 DT310















































































Search results

Summary of Contents for Univerge SV8100 DT310

Reviews:

Related manuals for Univerge SV8100 DT310

Brands by name

Popular brands

NEC Univerge SV8100 DT310, User Manual

Search results

Summary of Contents for Univerge SV8100 DT310

Reviews:

Related manuals for Univerge SV8100 DT310

Brands by name

Popular brands