NEC Univerge SV8100 DT310 User Manual Download

Page: 14 / 78

Keys And Parts

DT310/DT710

(2-Button without LCD)

(1) Call Indicator Lamp

Lamp at top corner of DT Series Display flashes
when a call terminates to the terminal or when a
message has been left. On the SV8100, this lamp
flashes fast when a call terminates to the terminal
and flashes slower when a message has been left.

(2) Programmable Keys

These keys can be programmed as Flexible Line
key/Programmable Feature Key by WebPro/
PCPro/PhonePro.

(3) Recall

Press key to finish an outside call and hear the dial
tone. With Centrex trunks press the recall key to
hook flash the line.

(4) Feature

Used to activate any features as terminal setup
functions.

(5)

Redial

(Last Number Call, Speed Calling-Station/Group)

Press key to activate redial feature.

(6) Conf

Press key to establish a three-way conversation.
LED on key lights when key is active.

(7) Answer

When LED on this key is flashing, press key to
answer a waiting call.

(8) Mic

Press the key to Mute/Un-Mute the speaker and/or
handset. LED on this key lights to show the key is
activated.

(9) Message

This key shows a message is waiting. Press this
key to access the Voice Mail system (if
programmed).

ABC

DEF

GHI

JKL

MNO

PQRS

TUV

WXYZ

HOLD

Transfer

Speaker

Recall

Feautre

Redial

Conf

Summary of Contents for Univerge SV8100 DT310















































































Search results

Summary of Contents for Univerge SV8100 DT310

Reviews:

Related manuals for Univerge SV8100 DT310

Brands by name

Popular brands

NEC Univerge SV8100 DT310, User Manual

Search results

Summary of Contents for Univerge SV8100 DT310

Reviews:

Related manuals for Univerge SV8100 DT310

Brands by name

Popular brands