background image

First Printing — August 1998

Copyright 1998

NEC Computer Systems Division

Packard Bell NEC, Inc.

1414 Massachusetts Avenue

Boxborough, MA 01719-2298

All Rights Reserved

Proprietary Notice and Liability Disclaimer

The information disclosed in this document, including all designs and related materials, is the
valuable property of NEC Computer Systems Division, Packard Bell NEC, Inc. (hereinafter “NEC
CSD”) and/or its licensors. NEC CSD and/or its licensors, as appropriate, reserve all patent,
copyright and other proprietary rights to this document, including all design, manufacturing,
reproduction, use, and sales rights thereto, except to the extent said rights are expressly granted to
others.

The NEC CSD product(s) discussed in this document are warranted in accordance with the terms of
the Warranty Statement accompanying each product. However, actual performance of each such
product is dependent upon factors such as system configuration, customer data, and operator
control. Since implementation by customers of each product may vary, the suitability of specific
product configurations and applications must be determined by the customer and is not warranted
by NEC CSD.

To allow for design and specification improvements, the information in this document is subject to
change at any time, without notice. Reproduction of this document or portions thereof without prior
written approval of NEC CSD is prohibited.

As an ENERGY star partner, NEC Computer Systems Division (NEC CSD) has determined that this product meets the

ENERGY star guidelines for energy efficiency.

FaxFlash is a service mark of NEC CSD, Packard Bell NEC, Inc.

NEC and PowerMate are registered trademarks of NEC Corporation, used under license.

ENERGY STAR is a U.S. registered trademark.

All other  product, brand, or trade names used in this publication are the trademarks or registered trademarks of their

respective trademark owners.

Summary of Contents for POWERMATE 5100 - SERVICE














































































































































































































































Reviews: