manualshive.com logo in svg

NEC PD789860, User Manual

The NEC PD789860 User Manual is an essential companion for maximizing the full potential of your NEC PD789860 product. Available for free download at our website, this comprehensive manual provides step-by-step instructions and valuable insights, ensuring a seamless user experience. Unlock the full potential of your device today!

Share
Download
background image

CHAPTER  9   8-BIT  TIMERS  30  AND  40 

 

User’s Manual  U14826EJ5V0UD 

102

9.4.2  Operation as 16-bit timer counter 

Timer 30 and timer 40 can be used as a 16-bit timer counter using cascade connection. In this case, 8-bit timer 

counter 30 (TM30) is the higher 8 bits and 8-bit timer counter 40 (TM40) is the lower 8 bits. 8-bit timer 40 controls 

reset and clear. 

The following modes can be used for the 16-bit timer counter. 

 

•

  Interval timer with 16-bit resolution 

•

  External event counter with 16-bit resolution 

•

  Square wave output with 16-bit resolution 

 

(1)  Operation as interval timer with 16-bit resolution 

The interval timer with 16-bit resolution repeatedly generates an interrupt at a time interval specified by the 

count value preset in 8-bit compare register 30 (CR30) and 8-bit compare register 40 (CR40). 

To operate as an interval timer with 16-bit resolution, settings must be made in the following sequence. 

 

<1>  Disable operation of 8-bit timer counter 30 (TM30) and 8-bit timer counter 40 (TM40) (TCE30 = 0, 

TCE40 = 0).  

<2>  Disable timer output of TMO (TOE40 = 0)

Note 1

. 

<3>  Set the count clock for timer 40 (see 

Tables 9-9

 and 

9-10

). 

<4>  Set the operation mode of timer 30 and timer 40 to 16-bit timer counter mode (see 

Figures 9-4

 and 

9-

5

). 

<5>  Set a count value in CR30 and CR40. 

<6>  Enable the operation of TM30 and TM40 (TCE40 = 1

Note 2

). 

 

Notes

 

1.

  Timer 40 only 

 

2.

  Start and clear of the timer in the 16-bit timer counter mode are controlled by TCE40 (the value 

of TCE30 is invalid). 

 

When the count values of TM30 and TM40 match the values set in CR30 and CR40 respectively, both TM30 

and TM40 are simultaneously cleared to 00H and counting continues.  At the same time, an interrupt request 

signal (INTTM40) is generated (INTTM30 is not generated). 

Tables 9-9 and 9-10 show interval time, and Figure 9-16 shows the timing of the interval timer operation. 

 

Caution  Be sure to stop the timer operation before overwriting the count clock with different data. 

 

Summary of Contents for PD789860



















































































































































































































Reviews:

No comments

Related manuals for PD789860

Ultratec SureFire Operation Manual preview
SureFire
Brand: Ultratec Pages: 33
Valcom V-1092 User Manual preview
V-1092
Brand: Valcom Pages: 3
Valcom V-1092 Technical Specifications preview
V-1092
Brand: Valcom Pages: 2
Yamaha CEmarking RCX221 User Manual preview
CEmarking RCX221
Brand: Yamaha Pages: 468
YASKAWA PROFINET V1000 Technical Manual preview
PROFINET V1000
Brand: YASKAWA Pages: 49
M-system MSP10 Instruction Manual preview
MSP10
Brand: M-system Pages: 17
SDC E4KP ENTRYCHECK Operating Instructions Manual preview
E4KP ENTRYCHECK
Brand: SDC Pages: 6
McIntosh MHT200 Owner'S Manual preview
MHT200
Brand: McIntosh Pages: 68
HANYOUNG NUX TPR-3N Instruction Manual preview
TPR-3N
Brand: HANYOUNG NUX Pages: 4
AGRI TRONIX DIGI-STAR GT400 Operator'S Manual preview
DIGI-STAR GT400
Brand: AGRI TRONIX Pages: 26
Zennio MAXinBOX 24 ZIO-MB24 User Manual preview
MAXinBOX 24 ZIO-MB24
Brand: Zennio Pages: 24
AUMA PROFOX PF-M100 Operation Instructions Manual preview
PROFOX PF-M100
Brand: AUMA Pages: 48
Meilhaus Electronic USB-GT Manual preview
USB-GT
Brand: Meilhaus Electronic Pages: 19
Magnimage LED-F706 User Manual preview
LED-F706
Brand: Magnimage Pages: 31
Electric Time 99B-MI User Manual preview
99B-MI
Brand: Electric Time Pages: 21
Warner Electric CBC-150 Series Installation And Operation Manual preview
CBC-150 Series
Brand: Warner Electric Pages: 4
MidNite Solar Brat Instructions Manual preview
Brat
Brand: MidNite Solar Pages: 24
Thundercomm TurboX C4290 Quick Start Manual preview
TurboX C4290
Brand: Thundercomm Pages: 5

Brands by name

Popular brands

Load more brands