Home
/
NEC
/
Express5800/iR120a-1E
/
User Manual

NEC Express5800/iR120a-1E, User Manual, Page: 361 / 378

Share

Page: 361 / 378

NEC Express5800/iR120a-1E User Manual Download Page 361

Upgrading Your Server 11-47

< 2.5-inch hard disk drive model with Onboard RAID Controller installed >

In standard configuration, the cable is connected with the SATA connector on mother board. You
need not to change cable connection.

< 2.5-inch hard disk drive model with Optional RAID Controller installed >

Disconnect the SAS/SATA cable from the SATA connector on mother board, then connect it with
the connector on Optional RAID Controller.

IMPORTANT:

In standard configuration of 2.5-inch hard disk drive

model, two SAS/SATA cables are connected. Be sure to connect both
SAS/SATA cables to the connectors on optional RAID Controller. You
cannot use the onboard RAID Controller and Optional RAID Controller
simultaneously.

«
...
359
360
361
362
363
...
»

Summary of Contents for Express5800/iR120a-1E



























































































































































































































































































































































































Reviews:

No comments