NEC Express5800/iR120a-1E User Manual Download Page 302

Page: 302 / 378

10-34 Troubleshooting

Physical device is not correctly displayed on Universal RAID Utility:

→

If you use LSI Embedded MegaRAID



, a part of information on a physical

device is not correctly displayed on Universal RAID Utility.

It is no problem.

Problems with N8190-127/131 FibreChannel Controller

When N8190-127/131 is used, the names of the Fibre Channel controllers may appear with different
names on Device Manager:

→

It is not a problem in operating the system. A directory that contains the driver
software NEC EXPRESSBUILDER DVD is also displayed.

[Windows Server 2008 64-bit (x64) Edition]

<Drive Letter>:\013\win\winnt\ws2008x64\elxstor\friendlyname.exe

[Windows Server 2008 32-bit (x86) Edition]

<Drive Letter>:\013\win\winnt\ws2008\elxstor\frendlyname.exe

Summary of Contents for Express5800/iR120a-1E



























































































































































































































































































































































































Search results

Summary of Contents for Express5800/iR120a-1E

Reviews:

NEC Express5800/iR120a-1E, User Manual, Page: 302 / 378

Search results

Summary of Contents for Express5800/iR120a-1E

Reviews: