NEC Express5800/iR120a-1E User Manual Download Page 207

Page: 207 / 378

Chapter 7

Installing Windows Server 2003

This section explains how to install the Windows Server 2003.

BEFORE INSTALLING WINDOWS SERVER 2003

Read the following notes or information before installing the Windows Server 2003.

Optional Board Supported by NEC EXPRESSBUILDER

The NEC EXPRESSBUILDER DVD attached to your server supports the following optional
boards;

Controllers supporting installation of OS with Express Setup

–

N8103-116A RAID Controller (128MB, RAID0/1)*

–

N8103-117A RAID Controller (128MB, RAID0/1/5/6)*

–

N8103-118A RAID Controller (256MB, RAID0/1/5/6)*

–

Onboard RAID Controller (LSI Embedded MegaRAID



)

Other controllers

–

N8103-104A SAS Controller*

–

N8103-107 SCSI Controller*

–

N8103-115 RAID Controller (512MB, RAID0/1/5/6)*

* Option

Summary of Contents for Express5800/iR120a-1E



























































































































































































































































































































































































Search results

Summary of Contents for Express5800/iR120a-1E

Reviews:

NEC Express5800/iR120a-1E, User Manual, Page: 207 / 378

Search results

Summary of Contents for Express5800/iR120a-1E

Reviews: