NEC Express5800/iR120a-1E User Manual Download Page 279

Page: 279 / 378

Troubleshooting 10-11

Error
code

Error message

Recommended Action

8068

Unsupported Processor Speed detected on
CPU Slot 1.

Contact your service representative.

8069

Unsupported Processor Speed detected on
CPU Slot 2.

8150

NVRAM Cleared by Jumper

Start SETUP and provide setting again.

8151

Password Cleared by Jumper

Start SETUP and set password again.

8160

Mismatch Processor Type/Speed detected
on Processor 1.

8161

Mismatch Processor Type/Speed detected
on Processor 2.

Contact your service representative.

None

Expansion ROM not initialized – PCI Mass
Storage Controller in slot xx

Disable initialization of the optional device
expansion ROM by using the BIOS SETUP
utility (see Chapter 4).

H/W Configuration of BMC is corrupted.
!! Update BMC F/W Configuration by
configuration tool !!
!! Refer to BMC configuration manual !!

Use the NEC EXPRESSBUILDER to
configure the remote management card
(see Chapter 8).

Memory Scramble mode disabled

Contact your service representative.

Summary of Contents for Express5800/iR120a-1E



























































































































































































































































































































































































Search results

Summary of Contents for Express5800/iR120a-1E

Reviews:

NEC Express5800/iR120a-1E, User Manual, Page: 279 / 378

Search results

Summary of Contents for Express5800/iR120a-1E

Reviews: