manualshive.com logo in svg

NEC Express5800/iR120a-1E, User Manual, Page: 121 / 378

Share
Download
NEC Express5800/iR120a-1E User Manual Download Page 121

Configuring Your Server    4-45

Check Consistency

Run LSI Software RAID Configuration Utility

Perform Check Consistency

Exit LSI Software RAID Configuration Utility

 

1. 

Run LSI Software RAID Configuration Utility.

 

2. 

Select "Check Consistency" from the TOP menu.

The "Virtual Drives" screen appears.

 

3. 

Move the cursor onto the virtual drive to be checked, and press 

Space

 to select it.

 

4. 

When virtual drive has been selected, press 

F10

 to start consistency check.

 

5. 

A confirmation screen for execution appears. Select "Yes".

The consistency check starts.

When the progress bar in the "Check Consistency Progress" screen indicates 100%, the
consistency check is completed.

 

6. 

Press 

Esc

 to return to the TOP menu and exit LSI Software RAID Configuration Utility.

IMPORTANT:

 Be sure to execute Check Consistency after creating

configuration.

Summary of Contents for Express5800/iR120a-1E



























































































































































































































































































































































































Reviews:

No comments