manualshive.com logo in svg

NEC Express5800/iR120a-1E, User Manual, Page: 221 / 378

Share
Download
NEC Express5800/iR120a-1E User Manual Download Page 221

Installing Windows Server 2003    7-15

Application Process of "Updating the System"

"Updating the System" applies the drivers necessary for NEC Express5800 Series.

Follow this process after Hotfix for Windows Server 2003 (KB921411) had been applied.

NOTE:

 If you install Windows CD-ROM that contains Service Pack 2

to your system, you do not have to apply Service pack 2 again.

 

1. 

Log on to the system with the account that has administrative privilege (e.g.
administrator).

 

2. 

Insert the NEC EXPRESSBUILDER DVD into the optical disk drive of server.

The Autorun Menu will be displayed

 

3. 

Left-click on [Setup Windows], and then click [Update the system].

NOTE:

 Right-clicking on the Autorun Menu produces the same

outcome.

 

4. 

Follow the message of the screen to proceed the application.

[OK] dialog box will be displayed.

NOTE:

 The following box appears during the update if you have

deployed a full installation of Windows Server 2003.
Wait until the update completes.

Summary of Contents for Express5800/iR120a-1E



























































































































































































































































































































































































Reviews:

No comments