manualshive.com logo in svg

NEC Express5800/iR120a-1E, User Manual, Page: 201 / 378

Share
Download
NEC Express5800/iR120a-1E User Manual Download Page 201

Installing Windows Server 2003 x64 Editions    6-33

How to Create a User-mode Process Dump File

Dr. Watson is a debugger for application errors. If any application error is detected, Dr. Watson
diagnoses the server and logs diagnostic information (log). Follow the procedure below and specify
Dr. Watson to collect diagnostic information.

 

1. 

Click [Run] on Start menu.

 

2. 

Type "drwtsn32.exe" in the [Open] box, and click [OK].

The [Dr. Watson for Windows] dialog box appears.

 

3. 

Specify the location to store the diagnostic information in the [Log File Path] box.

The diagnostic information will be stored with the file name "DRWTSN32.LOG".

NOTE:

 You can not specify network pass. Specify the pass on local

computer.

 

4. 

Specify the location of crash dump file in the [Crash Dump] box.

NOTE:

 "Crash Dump File" is a binary file that can be read with

Windows Debugger.

 

5. 

Select [Full] radio button from [Crash Dump Type].

 

6. 

Check the following check box on the [Options] box.

†

 Dump Symbol Table

†

 Dump All Thread Contexts

†

 Append TO Existing Log File

†

 Create Crash Dump File

For more information on each function above, refer to Online Help.

 

7. 

Click [OK].

Summary of Contents for Express5800/iR120a-1E



























































































































































































































































































































































































Reviews:

No comments