manualshive.com logo in svg

NAVIS A.467855.020, Reference Manual

Share
Download
NAVIS A.467855.020 Reference Manual Download Page 162

 

NAVIOR-24S 

™ 

 

     

Appendix C 

BINR Tool kit User’s Guide 

 

162 

 

 
NAVIOR-24S ™

 

    Revision 

V1.00 20.05.2008 

The channels info table contains the following information: 
o 

SNS

 SNS the SV belongs to. 

o 

SVn/Fn

 SV number for GPS SV and frequency number for GLONASS SV. 

o 

SNR

 Signal Noise Ratio 

o 

Mode

 Tracking mode 

 

 

auto

 Automatic tracking 

 

 

manual

 This channel was manually set to track this satellite. 

 

 

test

 Test mode during the receiver test. 

 

 

 

fault 

Broken channel. 

o 

Status

 A bit mask of measurements status. See table below. 

o 

PR

 Pseudo range modulo 1 msec. 

o 

PD

 Pseudo Doppler 

 

Table IV-5 - The status bit mask is composed of the following bits. 

Bit#  

Meaning 

0 Non-zero 

SNR. 

1 

Pseudo range and pseudo Doppler are measured 

2 

Smoothed range is measured 

3 

Pseudo phase is measured 

4 Time 

synchronization 

5 reserved 

6 reserved 

7 reserved 

8 

Ephemeris data are available 

9 

Almanac data are available 

10 reserved 

11 GLONASS-M 

satellite 

12 

Measurements are ready to be used in solution 

13 

Measurement have been used in solution 

14 reserved 

15  

Measurements are RAIM-discarded 

 

Summary of Contents for A.467855.020





































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands