manualshive.com logo in svg

natus OLYMPIC STERILE-DRIER 43, Instruction Manual, Page: 38 / 62

Share
Download
natus OLYMPIC STERILE-DRIER 43 Instruction Manual Download Page 38

6-8

OLYMPIC STERILE-DRIER 

Model 43/44 Instruction Manual

Repair Procedures

6

Connect the thermal probe cable connector (wires 27, 29, and 30) to J3 on the 

control panel PCB.

7

Secure the probe cable to the two cable tie mounts with cable ties.

8

Insert the side access panel, then secure the tray brackets and trays with the 

saved hardware.

9

Replace the filter on the plenum, connect the thermal cut-out wires, then 

connect the plenum hold-down springs.

10

Insert the front cover.

11

Tighten the screws just inside the Drier door.

12

Plug in the power cord, then press the power switch to the 

ON

 (|) position.

13

Test the device for proper operation (see page 2-4).

Replacing the Heater Control Relay K2

If the heat is off or very low, the heater control relay may need to be replaced.

Required Items:

„

Heater control relay (part no. 200041)

„

Screwdriver

„

Thermal compound (part no. 900006)

To remove the heater control relay:

1

Press the power switch to the 

OFF

 (O) position, then unplug the power cord.

2

Remove the upper white door seal and loosen—but do not remove—screws just 

inside the Drier door (behind the door stop) (see Figure 4.2 on page 4-3).

3

Pull out and remove the front cover (see Figure 4.3 on page 4-3).

4

Locate the heater control relay K2 in the upper portion of the drying cabinet (for 

Model 43, see drawing 700199; for Model 44, see drawing 700203), then 

disconnect the wires from the heater control relay (see Figure 6.3).

NOTE

#

Remove slack from the thermal probe cable by gently pulling the excess cable into the 
upper cabinet. Ensure that the cable is not dangling behind the tube holder.

CAUTION

ESD-sensitive equipment. Use appropriate precautions to prevent ESD.

WARNING

Electrical shock hazard when the front panel is removed.

NOTE

#

To avoid reconnecting the heater control relay incorrectly, clearly mark the wires before 
disconnecting (see Figure 6.3).

Summary of Contents for OLYMPIC STERILE-DRIER 43































































Reviews:

No comments