manualshive.com logo in svg

natus OLYMPIC STERILE-DRIER 43, Instruction Manual, Page: 16 / 62

Share
Download
natus OLYMPIC STERILE-DRIER 43 Instruction Manual Download Page 16

2-6

OLYMPIC STERILE-DRIER 

Model 43/44 Instruction Manual

Testing the Drier

Figure 2.7

Accessing the blower assembly

5

Separate the plenum from the casing (or HEPA filter), and then lift the plenum 

and unscrew the heater from the socket. Ensure that the socket cap is tight, and 

then screw the heater firmly back into place.

6

Replace the plenum; ensure that the plenum and filter are fully seated. Install 

the plenum hold-down springs, and then reconnect the thermal cut-out wires.

7

Position the front cover, tighten the screws, and then push the white door seal 

into place.

8

Plug in the power cord, and press the power switch to the 

ON

 (|) position.

9

Test for proper operation (see 

Testing the Drier

).

Testing the Drier

Perform the test procedure to ensure the Drier is working properly after performing 
assembly and service procedures.

To test the Drier:

1

Plug in the power cord, and press the power switch to the 

ON

 (|) position.

2

Set the heat control to midway between high and low, then set the timer to 

ON

.

3

Ensure that the blowers are operating—warm air should blow from the screened 

panel above the tube holder assembly inside the drying cabinet.

HEPA filter 

FRONT

Acorn nuts and washers

Blower

Blower bracket

Blower filter plate

Plenum assembly

Note

: Pull together the two springs to 

unlatch them, and then separate. Lift 
the metal box up to access the heaters.

Summary of Contents for OLYMPIC STERILE-DRIER 43































































Reviews:

No comments