natus OLYMPIC STERILE-DRIER 43 Instruction Manual Download Page 40 | Manualshive

Page: 40 / 62

natus OLYMPIC STERILE-DRIER 43 Instruction Manual Download Page 40

6-10

OLYMPIC STERILE-DRIER

Model 43/44 Instruction Manual

Repair Procedures

Replacing the Blower Control Relay

(Model 44 only)

If the timer is on, but the blower doesn’t operate, replace the blower control relay.

Required Items:

Blower control relay (part no. 200041)

Screwdriver

To replace the blower control relay:

1

Press the power switch to the

OFF

(O) position, then unplug the power cord.

2

Remove the upper white door seal and loosen—but no not remove—the screws

just inside the Drier door (behind the door stop) (see Figure 4.2 on page 4-3).

3

Pull out and remove the front cover (see Figure 4.3 on page 4-3).

4

Unplug the blower control relay from the socket (see drawing 700203).

5

Remove the old relay, then place the new relay into position.

6

Position the front cover, tighten the screws, then push the door seal into place.

7

Plug in the power cord, then press the power switch to the

ON

(|) position.

8

Test the device for proper operation (see page 2-4).

WARNING

Electrical shock hazard when the front panel is removed.

«
...
38
39
40
41
42
...
»

Summary of Contents for OLYMPIC STERILE-DRIER 43































































Reviews:

No comments