manualshive.com logo in svg

natus OLYMPIC STERILE-DRIER 43, Instruction Manual, Page: 29 / 62

Share
Download
natus OLYMPIC STERILE-DRIER 43 Instruction Manual Download Page 29

OLYMPIC STERILE-DRIER 

Model 43/44 Instruction Manual

5-1

S e c t i o n

5

Troubleshooting

Should you experience difficulty when operating your Drier, consult the following 
table. For problems not listed in the table, contact Natus Medical (see page 5-2).

Table 5.1

Troubleshooting chart 

Problem

Probable Cause

Solution

Power switch on but 
indicator and display 
don’t illuminate

No power

Ensure that the power cord is plugged 
in to an appropriate electrical outlet.

Check the external circuit breaker.

Blown fuse

Replace the fuse (see page 6-2).

Defective control PCB

Replace the control PCB (see 
page 6-4).

Timer on or in timed 
position, but blower 
doesn’t operate or 
intermittent blower 
operation

Malfunctioning blower

Replace the blower and reset the 
thermostat (see page 6-11).

Blower fan blocked

Remove the blockage, free the fan, then 
reset the thermal cut-out (see 
page 6-14).

Loose wire connection 
at J-5 or J-6 on control 
PCB

Ensure that the screws at the J-5 and 
J-6 connections are tight.

Gently pull the wires to ensure that the 
wires are tightly secured.

Defective control PCB

Replace the control PCB (see 
page 6-4).

Relay hold-down clip is 
loose

Follow directions for replacing the 
blower relay (see page 6-10, step 1 
through step 3). Ensure that the relay 
hold-down clip is over the relay switch.

Defective blower relay 
(Model 44)

Replace the blower relay (see 
page 6-10).

Summary of Contents for OLYMPIC STERILE-DRIER 43































































Reviews:

No comments