manualshive.com logo in svg

natus OLYMPIC STERILE-DRIER 43, Instruction Manual, Page: 32 / 62

Share
Download
natus OLYMPIC STERILE-DRIER 43 Instruction Manual Download Page 32

6-2

OLYMPIC STERILE-DRIER 

Model 43/44 Instruction Manual

Repair Procedures

Replacing the Main and Transformer Fuses

If the device is plugged in but won’t turn on, the fuse may have to be replaced.

Required Items:

„

Fuse (part no. 200021)

„

Screwdriver

To replace the fuses:

1

Press the power switch to the 

OFF

 (O) position, then unplug the power cord.

2

Remove the upper white door seal and loosen—but do not remove—screws just 

inside the Drier door (behind the door stop) (see Figure 4.2 on page 4-3).

3

Pull out and remove the front cover (see Figure 4.3 on page 4-3).

4

Locate, remove, and replace the fuse(s).

5

Position the front cover, tighten the screws, and push the upper white door seal 

into place.

6

Reconnect the power cord to the electrical outlet.

7

Test the device for proper operation (see page 2-4).

CAUTION

Replace the fuse only with a new fuse of the same type and value.

WARNING

Electrical shock hazard when the front panel is removed.

Summary of Contents for OLYMPIC STERILE-DRIER 43































































Reviews:

No comments