manualshive.com logo in svg

natus OLYMPIC STERILE-DRIER 43, Instruction Manual, Page: 12 / 62

Share
Download
natus OLYMPIC STERILE-DRIER 43 Instruction Manual Download Page 12

2-2

OLYMPIC STERILE-DRIER 

Model 43/44 Instruction Manual

Assembly

Electrical Requirements

The Olympic Sterile-Drier Model 43 is available in the following configurations:

„

120V~, 60 Hz, 8A (standard configuration for the United States and Canada)

„

100V~, 50 Hz, 9.5A

„

100V~, 60 Hz, 9.5A

„

220-230V~, 50 Hz, 4.5A

„

220-230V~, 60 Hz, 4.5A

The Olympic Sterile-Drier Model 44 is available in the following configurations:

„

120V~, 60 Hz, 16A (standard configuration for the United States and Canada)

„

100V~, 50 Hz, 18A

„

100V~, 60 Hz, 18A

„

220-230V~, 50 Hz, 9A

„

220-230V~, 60 Hz, 9A

Assembly

To assemble the Drier:

1

After uncrating, install the leveling feet, then carefully stand the drier upright.

2

Clean the metal surfaces with soap and water or liquid disinfectant. Clean the 

plastic doors with soap and water.

3

After the Drier is in place, adjust the leveling feet (see Figure 2.1).

CAUTION

This device must be connected directly to a properly grounded hospital-grade 
electrical outlet.

NOTE

#

„

Due to amperage draw, Model 44 requires a dedicated over-current protection device.

„

Supply voltage fluctuations are not to exceed 10% of the nominal supply voltage.

CAUTION

Only qualified technicians should assemble the device.

CAUTION

Never use alcohol to clean the doors, as alcohol will damage the Plexiglas

®

.

Summary of Contents for OLYMPIC STERILE-DRIER 43































































Reviews:

No comments