manualshive.com logo in svg

natus OLYMPIC STERILE-DRIER 43, Instruction Manual, Page: 39 / 62

Share
Download
natus OLYMPIC STERILE-DRIER 43 Instruction Manual Download Page 39

OLYMPIC STERILE-DRIER 

Model 43/44 Instruction Manual

6-9

Repair Procedures

Figure 6.3

Disconnecting the heater control relay

5

Remove and save the two screws that secure the relay to the heatsink, then 

remove the old relay.

To install the new heater relay:

1

Coat the contact surface of the heatsink with a thin, uniform layer of heatsink 

compound.

2

Place the new relay with terminals 2 and 4 toward the front of the device (for 

Model 43, see wiring diagram 700199; for Model 44, see wiring diagram 

700203).

3

Attach the wires to the heater control relay (see page A-1).

4

Insert the front cover, then tighten the screws just inside the Drier door.

5

Plug in the power cord, then press the power switch to the 

ON

 (|) position.

6

Test the device for proper operation (see page 2-4).

Heatsink

Connector 

bracket

Screw

Star 

washers

Wire #28 at 

terminal #4

Wire #25 at 

terminal #3

Screws (x2) 

secure relay to 

heatsink

Wire #33 

 

(Model 44 only)

Wire #9 at 
terminal #1

Wire #11 at 
terminal #2

Double wire 
at terminal 
#2 (Model 
44 only)

NOTE

#

Ensure that the wires are placed on the relay terminals per the wiring diagrams and that 
washers and screws are arranged (see Figure 6.3).

Summary of Contents for OLYMPIC STERILE-DRIER 43































































Reviews:

No comments