manualshive.com logo in svg

National Semiconductor CP3BT26, User Manual

The National Semiconductor CP3BT26 user manual is an essential companion for efficiently operating this cutting-edge product. With just a few clicks, users can conveniently download this comprehensive manual for free from our website, ensuring seamless navigation and superior performance.

Share
Download
background image

145

www.national.com

CP3

BT26

On the receiver side, only the valid data bits which were re-
ceived during the slots assigned to this interface are copied
into the receive FIFO or DMA registers. The assignment of
slots to the receiver is specified by the Receive Slot Assign-
ment bits (RXSA) in the ATCR register. It can also be spec-
ified whether the received data is copied into the receive
FIFO or into the corresponding DMA receive register. There
is one DMA receive register (ARDRn) for each of the maxi-
mum four data slots. Each slot may be configured individu-
ally.

Figure 67 shows the frame timing while operating in network
mode with four slots per frame, slot 1 assigned to the inter-
face, and a long frame sync interval.

Figure 67.

Network Mode Frame

IRQ Support

If DMA is not enabled for a receive slot n (RXDSAn = 0), all
data received in this slot is loaded into the receive FIFO. An
IRQ is asserted as soon as the number of data bytes or
words in the receive FIFO is greater than a configured warn-
ing limit.

If DMA is not enabled for a transmit slot n (TXDSAn = 0), all
data to be transmitted in this slot are read from the transmit
FIFO. An IRQ is asserted as soon as the number data bytes
or words available in the transmit FIFO is equal or less than
a configured warning limit.

DMA Support

If DMA support is enabled for a receive slot n (RXDSA0 =
1), all data received in this slot is only transferred from the
ARSR into the corresponding DMA receive register
(ARDRn). A DMA request is asserted when the ARDRn reg-
ister is full.

If DMA is enabled for a transmit slot n (TXDSAn = 1), all data
to be transmitted in slot n are read from the corresponding
DMA transmit register (ATDRn). A DMA request is asserted
to the DMA controller when the ATDRn register is empty.

Figure 68 illustrates the data flow for IRQ and DMA support
in network mode, using four slots per frame and DMA sup-

port enabled for slots 0 and 1 in receive and transmit direc-
tion.

Figure 68.

IRQ/DMA Support in Network Mode

If the interface operates in synchronous mode, the receiver
uses the transmit bit clock (SCK) and transmit frame sync
signal (SFS). This allows the pins used for the receive bit
clock (SRCLK) and receive frame sync (SRFS) to be used
as additional frame sync signals in network mode. The extra
frame sync signals are useful when the audio interface com-
municates to more than one codec, because codecs typical-
ly start transmission immediately after the frame sync pulse.
The SRCLK pin is driven with a frame sync pulse at the be-
ginning of the second slot (slot 1), and the SRFS pin is driv-
en with a frame sync pulse at the beginning of slot 2.
Figure 69 shows a frame timing diagram for this configura-
tion, using the additional frame sync signals on SRCLK and
SRFS to address up to three devices.

Shift Data

(STD/SRD)

High-impedance

Unused Slots

Slot1

Frame

Slot0

Long Frame Sync

(SFS/SRFS)

Data

(ignored)

Data

(ignored)

Data

(valid)

DS055

DMA Slot

Assignment

Slot 1 data

Slot 0 data

Slot 2 and 3 data

ARSR

SRD

ARDR 0

DMA
Request 1

ARDR 1

DMA
Request 3

ARDR 2

ARDR 3

RX

FIFO

IRQ

DMA Slot

Assignment

Slot 1 data

Slot 0 data

ATSR

STD

ATDR 0

DMA
Request 0

ATDR 1

DMA
Request 2

ATDR 2

ATDR 3

TX

FIFO

IRQ

Slot 2 and 3 data

DS056

Summary of Contents for CP3BT26























































































































































































































































































Reviews:

No comments

Related manuals for CP3BT26

3Com 3CRWEASY96A Quick Start Manual preview
3CRWEASY96A
Brand: 3Com Pages: 8
Xinje XS Series User Manual preview
XS Series
Brand: Xinje Pages: 57
Supero AOC-SIMLC User Manual preview
AOC-SIMLC
Brand: Supero Pages: 68
RuggedCom RUGGEDMAX WIN7000 Installation Manual preview
RUGGEDMAX WIN7000
Brand: RuggedCom Pages: 42
Compaq StorageWorks AIT 35GB AutoLoader Overview And Installation preview
StorageWorks AIT 35GB AutoLoader
Brand: Compaq Pages: 4
Aqua Computer Aquaduct 360 XT Operating And Assembly Manual preview
Aquaduct 360 XT
Brand: Aqua Computer Pages: 28
ENERMAX ELC-LTTR240-TBP User Manual preview
ELC-LTTR240-TBP
Brand: ENERMAX Pages: 16
Buffalo LinkStation Quick Setup Manual preview
LinkStation
Brand: Buffalo Pages: 2
Roland Super Sound Set SR-JV80-07 Owner'S Manual preview
Super Sound Set SR-JV80-07
Brand: Roland Pages: 8
Schrack Technik HSERG245GS Instruction Sheet preview
HSERG245GS
Brand: Schrack Technik Pages: 2
red lion Yaskawa 2000 Information Sheet preview
Yaskawa 2000
Brand: red lion Pages: 5
QuickLink QL-CXS Installation Manual preview
QL-CXS
Brand: QuickLink Pages: 8
Sangoma A200 Analog Installation Manual preview
A200 Analog
Brand: Sangoma Pages: 6
PMD DK55110 Manual preview
DK55110
Brand: PMD Pages: 74
Bitspower BPTA-CPUMS-V2-SKA Instruction Manual preview
BPTA-CPUMS-V2-SKA
Brand: Bitspower Pages: 6
Comtrend Corporation WAP-5922MP Quick Install Manual preview
WAP-5922MP
Brand: Comtrend Corporation Pages: 4
Cooler Master Masterliquid ML240L RGB Manual preview
Masterliquid ML240L RGB
Brand: Cooler Master Pages: 18
ETAS ES1392.1 User Manual preview
ES1392.1
Brand: ETAS Pages: 36

Brands by name

Popular brands

Load more brands