![background image](http://html.mh-extra.com/html/national-semiconductor/cp3bt26/cp3bt26_user-manual_710369056.webp)
www.national.com
56
CP3BT26
12.0 Power Management
The Power Management Module (PMM) improves the effi-
ciency of the CP3BT26 by changing the operating mode
(and therefore the power consumption) according to the re-
quired level of device activity. The device implements four
power modes:
Active
Power Save
Idle
Halt
Table 24 summarizes the differences between power
modes: the state of the high-frequency oscillator (on or off),
the System Clock source (clock used by most modules),
and the clock source used by the Timing and Watchdog
Module (TWM). The high-frequency oscillator generates the
12-MHz Main Clock, and the low-frequency oscillator gener-
ates a 32.768 kHz clock. The Slow Clock can be driven by
the 32.768 kHz clock or a scaled version of the Main Clock.
The low-frequency oscillator continues to operate in all four
modes and power must be provided continuously to the de-
vice power supply pins. In Halt mode, however, Slow Clock
does not toggle, and as a result, the TWM timer and Watch-
dog Module do not operate. For the Power Save and Idle
modes, the high-frequency oscillator can be turned on or off
under software control, as long as the low-frequency oscil-
lator is used to drive Slow Clock.
Table 25 shows the clock sources used by the CP3BT26 de-
vice modules and their behavior in each power mode.
* The Analog/Digital Converter (ADC) module is not auto-
matically disabled by entering Halt mode, however its clock
is stopped so no conversions may be performed in Halt
mode. For maximum power savings, software must disable
the ADC module before entering Halt mode.
A module shown as On/Off in Table 25 may be enabled or
disabled by software. A module shown as Active continues
to operate even while its clock is suspended, which allows
wake-up events to be processed during Idle and Halt
modes.
The Random Number Generator (RNG) module has two os-
cillators which operate independently of the rest of the sys-
tem. For maximum power savings, software must disable
these oscillators.
12.1
ACTIVE MODE
In Active mode, the high-frequency oscillator is active and
generates the 12-MHz Main Clock. The 32.768 kHz oscilla-
tor is active and may be used to generate the Slow Clock.
The PLL can be active or inactive, as required. Most on-chip
modules are driven by the System Clock. The System Clock
can be the PLL Clock after a programmable divider or the
12-MHz Main Clock. The activity of peripheral modules is
controlled by their enable bits.
Power consumption can be reduced in this mode by selec-
tively disabling modules and by executing the WAIT instruc-
tion. When the WAIT instruction is executed, the CPU stops
executing new instructions until it receives an interrupt sig-
nal. After reset, the CP3BT26 is in Active Mode.
12.2
POWER SAVE MODE
In Power Save mode, Slow Clock is used as the System
Clock which drives the CPU and most on-chip modules. If
Slow Clock is driven by the 32.768 kHz oscillator and no on-
chip module currently requires the 12-MHz Main Clock, soft-
ware can disable the high-frequency oscillator to further re-
duce power consumption. Auxiliary Clocks 1 and 2 can be
turned off under software control before switching to a re-
duced power mode, or they may remain active as long as
Main Clock is also active. If the system does not require the
PLL output clock, the PLL can be disabled. Alternatively, the
Main Clock and the PLL can also be controlled by the Hard-
ware Clock Control function, if enabled. The clock architec-
ture is described in Section 11.0.
The Bluetooth LLC can either be switched to the 32 kHz
clock internally in the module, or it remains running off Aux-
iliary clock 1 as long as the Main Clock and Auxiliary Clock
1 are enabled.
In Power Save mode, some modules are disabled or their
operation is restricted. Other modules, including the CPU,
continue to function normally, but operate at a reduced clock
rate. Details of each module’s activity in Power Save mode
are described in each module’s descriptions.
It is recommended to keep CPU activity at a minimum by ex-
ecuting the WAIT instruction to guarantee low power con-
sumption in the system.
Table 24
Power Mode Operating Summary
Mode
High-Frequency
Oscillator
System
Clock
TWM Clock
Active
On
Main Clock
Slow Clock
Power Save On or Off
Slow Clock
Slow Clock
Idle
On or Off
None
Slow Clock
Halt
Off
None
None
Table 25
Module Activity Summary
Module
Power Mode
Clock
Source
Active
Power
Save
Idle
Halt
CPU
On
On/Off
Off
Off
System
MIWU
On
On
Active Active
System
PMM
On
On
On
Active Slow Clock
TWM
On
On
On
Off
Slow Clock
USB
On/Off On/Off On/Off
Off
PLL Clock
Bluetooth
On/Off On/Off On/Off
Off
Aux 1 Clock
AAI
On/Off On/Off On/Off
Off
Aux 1 Clock
CVSD/PCM On/Off On/Off On/Off
Off
Aux 2 Clock
ADC
On/Off On/Off On/Off
Off*
Aux 2 Clock
All Others
On/Off On/Off
Off
Off
System