manualshive.com logo in svg

National Semiconductor CP3BT26, User Manual

The National Semiconductor CP3BT26 user manual is an essential companion for efficiently operating this cutting-edge product. With just a few clicks, users can conveniently download this comprehensive manual for free from our website, ensuring seamless navigation and superior performance.

Share
Download
background image

69

www.national.com

CP3

BT26

All of the port registers are byte-wide read/write registers,
except for the port data input registers, which are read-only
registers. Each register bit controls the function of the cor-
responding port pin. For example, PGDIR.2 (bit 2 of the
PGDIR register) controls the direction of port pin PG2.

14.1.1

Port Alternate Function Register (PxALT)

The PxALT registers control whether the port pins are used
for general-purpose I/O or for their alternate function. Each
port pin can be controlled independently. 

A clear bit in the alternate function register causes the cor-
responding pin to be used for general-purpose I/O. In this
configuration, the output buffer is controlled by the direction
register (PxDIR) and the data output register (PxDOUT).
The input buffer is visible to software as the data input reg-
ister (PxDIN).

A set bit in the alternate function register (PxALT) causes
the corresponding pin to be used for its peripheral I/O func-
tion. When the alternate function is selected, the output
buffer data and TRI-STATE configuration are controlled by
signals from the on-chip peripheral device. 

A reset operation clears the port alternate function regis-
ters, which initializes the pins as general-purpose I/O ports.
This register must be enabled before the corresponding al-
ternate function is enabled. 

PxALT

The PxALT bits control whether the corre-
sponding port pins are general-purpose I/O
ports or are used for their alternate function by
an on-chip peripheral.
0 

–

General-purpose I/O selected.

1 

–

Alternate function selected.

14.1.2

Port Direction Register (PxDIR)

The port direction register (PxDIR) determines whether
each port pin is used for input or for output. A clear bit in this
register causes the corresponding pin to operate as an in-
put, which puts the output buffer in the high-impedance
state. A set bit causes the pin to operate as an output, which
enables the output buffer.

A reset operation clears the port direction registers, which
initializes the pins as inputs.

PxDIR

The PxDIR bits select the direction of the cor-
responding port pin.
0 

–

Input.

1 

–

Output.

14.1.3

Port Data Input Register (PxDIN)

The data input register (PxDIN) is a read-only register that
returns the current state on each port pin. The CPU can
read this register at any time even when the pin is config-
ured as an output.

PxDIN

The PxDIN bits indicate the state on the cor-
responding port pin.
0 

–

Pin is low.

1 

–

Pin is high.

14.1.4

Port Data Output Register (PxDOUT)

The data output register (PxDOUT) holds the data to be
driven on output port pins. In this configuration, writing to
the register changes the output value. Reading the register
returns the last value written to the register. 

A reset operation leaves the register contents unchanged.
At power-up, the PxDOUT registers contain unknown val-
ues. 

PxDOUT

The PxDOUT bits hold the data to be driven
on pins configured as outputs in general-pur-
pose I/O mode.
0 

–

Drive the pin low.

1 

–

Drive the pin high.

14.1.5

Port Weak Pull-Up Register (PxWPU)

The weak pull-up register (PxWPU) determines whether the
port pins have a weak pull-up on the output buffer. The pull-
up device, if enabled by the register bit, operates in the gen-
eral-purpose I/O mode whenever the port output buffer is
disabled. In the alternate function mode, the pull-ups are al-
ways disabled. 

A reset operation clears the port weak pull-up registers,
which disables all pull-ups.

PxWPU

The PxWPU bits control whether the weak
pull-up is enabled.
0 

–

Weak pull-up disabled.

1 

–

Weak pull-up enabled.

7

0

PxALT

7

0

PxDIR

7

0

PxDIN

7

0

PxDOUT

7

0

PxWPU

Summary of Contents for CP3BT26























































































































































































































































































Reviews:

No comments

Related manuals for CP3BT26

Rane CP 31 Datasheet preview
CP 31
Brand: Rane Pages: 4
3Com OfficeConnect WX2200 User Manual preview
OfficeConnect WX2200
Brand: 3Com Pages: 204
SUNRICH TECHNOLOGY C-330 User Manual preview
C-330
Brand: SUNRICH TECHNOLOGY Pages: 5
Zonet ZUN2200 Quick Installation Manual preview
ZUN2200
Brand: Zonet Pages: 2
u-blox ANT-B10 User Manual preview
ANT-B10
Brand: u-blox Pages: 29
Parker PCH1 T P Series User Manual preview
PCH1 T P Series
Brand: Parker Pages: 107
JETWAY HBJC924R3288DG2NS Series Quick Installation Manual preview
HBJC924R3288DG2NS Series
Brand: JETWAY Pages: 6
C&T Solution RCO-3000 Series User Manual preview
RCO-3000 Series
Brand: C&T Solution Pages: 96
QNAP TS-1283XU-RP User Manual preview
TS-1283XU-RP
Brand: QNAP Pages: 54
JYTEK PCIe/PXIe-6301 Series User Manual preview
PCIe/PXIe-6301 Series
Brand: JYTEK Pages: 46
Z3 Technology Z3-SBE264-10 User Instructions preview
Z3-SBE264-10
Brand: Z3 Technology Pages: 67
ebm-papst R3G560-AH02-03 Operating Instructions Manual preview
R3G560-AH02-03
Brand: ebm-papst Pages: 13
Powerleap PL-PROMMX Manual preview
PL-PROMMX
Brand: Powerleap Pages: 28
Accusys ACS-7630 User Manual preview
ACS-7630
Brand: Accusys Pages: 34
FOR-A USF-105PS Operation Manuals preview
USF-105PS
Brand: FOR-A Pages: 37
ICP DAS USA VEX-112 Quick Start Manual preview
VEX-112
Brand: ICP DAS USA Pages: 8
IBASE Technology SI-22-415 User Manual preview
SI-22-415
Brand: IBASE Technology Pages: 49
Curtiss-Wright GTS/DEC/003 Manual preview
GTS/DEC/003
Brand: Curtiss-Wright Pages: 10

Brands by name

Popular brands

Load more brands