manualshive.com logo in svg

National Semiconductor CP3BT26, User Manual

The National Semiconductor CP3BT26 user manual is an essential companion for efficiently operating this cutting-edge product. With just a few clicks, users can conveniently download this comprehensive manual for free from our website, ensuring seamless navigation and superior performance.

Share
Download
background image

17

www.national.com

CP3

BT26

5.4

CONFIGURATION REGISTER (CFG)

The CFG register is used to enable or disable various oper-
ating modes and to control optional on-chip caches. Be-
cause the CP3BT26 does not have cache memory, the
cache control bits in the CFG register are reserved. All CFG
bits are cleared on reset.

ED

The Extended Dispatch bit selects whether
the size of an entry in the interrupt dispatch ta-
ble (IDT) is 16 or 32 bits. Each entry holds the
address of the appropriate exception handler.
When the IDT has 16-bit entries, and all ex-
ception handlers must reside in the first 128K
of the address space. The location of the IDT
is held in the INTBASE register, which is not
affected by the state of the ED bit.
0 

–

Interrupt dispatch table has 16-bit entries.

1 

–

Interrupt dispatch table has 32-bit entries.

SR

The Short Register bit enables a compatibility
mode for the CR16B large model. In the
CR16C core, registers R12, R13, and RA are
extended to 32 bits. In the CR16B large mod-
el, only the lower 16 bits of these registers are
used, and these “short registers” are paired
together for 32-bit operations. In this mode,
the (RA, R13) register pair is used as the ex-
tended RA register, and address displace-
ments relative to a single register are
supported with offsets of 0 and 14 bits in place
of the index addressing with these displace-
ments.
0 

–

32-bit registers are used.

1 

–

16-bit registers are used (CR16B mode).

15

10

9

8

7

6

5

2

1

0

Reserved

SR ED 0

0

Reserved

0

0

Summary of Contents for CP3BT26























































































































































































































































































Reviews:

No comments

Related manuals for CP3BT26

Aaeon UP Squared 6000 Edge Computing Kit User Manual preview
UP Squared 6000 Edge Computing Kit
Brand: Aaeon Pages: 59
Dave Embedded Systems ARM Cortex-A9 MPCore Quick Start Manual preview
ARM Cortex-A9 MPCore
Brand: Dave Embedded Systems Pages: 67
Rane CP 31 Datasheet preview
CP 31
Brand: Rane Pages: 4
Yamaha DX7mega128 Install Manual preview
DX7mega128
Brand: Yamaha Pages: 6
Yamaha DX7 MiniMAX User Manual preview
DX7 MiniMAX
Brand: Yamaha Pages: 4
Yamaha DME Designer Setup Manual preview
DME Designer
Brand: Yamaha Pages: 22
Yamaha PLG100-VL Eigentümer-Handbuch preview
PLG100-VL
Brand: Yamaha Pages: 49
Analog Devices ADAU1961 Manual preview
ADAU1961
Brand: Analog Devices Pages: 76
Roland MSL-15 Owner'S Manual preview
MSL-15
Brand: Roland Pages: 12
Ensemble Designs Avenue Express Control Panel Data Pack preview
Avenue Express Control Panel
Brand: Ensemble Designs Pages: 19
impinj Speedway Revolution Installation And Operation Manual preview
Speedway Revolution
Brand: impinj Pages: 60
Ubiquiti UniFi Cloud Key Quick Start Manual preview
UniFi Cloud Key
Brand: Ubiquiti Pages: 13
PaloAlto Networks ION 1000 Hardware Reference Manual preview
ION 1000
Brand: PaloAlto Networks Pages: 28
Digital Equipment ChannelWorks Network Installer Manual preview
ChannelWorks
Brand: Digital Equipment Pages: 90
IEI Technology WAFER-EHL Series User Manual preview
WAFER-EHL Series
Brand: IEI Technology Pages: 142
RadioSPECTRAL ICOM IC-7300 Installation Manual preview
ICOM IC-7300
Brand: RadioSPECTRAL Pages: 2
ZALMAN VF2000 LED User Manual preview
VF2000 LED
Brand: ZALMAN Pages: 9
Holtek HT68F30 Manual preview
HT68F30
Brand: Holtek Pages: 280

Brands by name

Popular brands

Load more brands