manualshive.com logo in svg

National Semiconductor CP3BT26, User Manual

The National Semiconductor CP3BT26 user manual is an essential companion for efficiently operating this cutting-edge product. With just a few clicks, users can conveniently download this comprehensive manual for free from our website, ensuring seamless navigation and superior performance.

Share
Download
background image

www.national.com

30

CP3BT26

7.2

MODULE STATUS REGISTER (MSTAT)

The MSTAT register is a byte-wide, read-only register that
indicates the general status of the device. The MCFG regis-
ter format is shown below. 

OENV2:0

The Operating Environment bits hold the
states sampled from the ENV[2:0] input pins
at reset. These states are controlled by exter-
nal hardware at reset and are held constant in
the register until the next reset.

PGMBUSY

The Flash Programming Busy bit is automati-
cally set when either the program memory or
the data memory is being programmed or
erased. It is clear when neither of the memo-
ries is busy. When this bit is set, software must
not attempt to program or erase either of
these two memories. This bit is a copy of the
FMBUSY bit in the FMSTAT register.
0 

–

Flash memory is not busy.

1 

–

Flash memory is busy.

DPGMBUSY The Data Flash Programming Busy indicates

that the flash data memory is being erased or
a pipelined programming sequence is current-
ly ongoing. Software must not attempt to per-
form any write access to the flash program
memory at this time, without also polling the
FSMSTAT.FMFULL bit in the flash memory in-
terface. The DPGMBUSY bit is a copy of the
FMBUSY bit in the FSMSTAT register.
0 

–

Flash data memory is not busy.

1 

–

Flash data memory is busy.

WDRST

The Watchdog Reset bit indicates that a
Watchdog timer reset has occurred. Write a 1
to this bit to clear it. Power-on reset also
clears this bit.
0 

–

No Watchdog timer reset has occurred
since this bit was last cleared.

1 

–

A Watchdog timer reset has occurred
since this bit was last cleared.

ISPRST

The Software ISP Reset bit indicates that a
software ISP reset has occurred since the bit
was last cleared. This bit is cleared by a
SWRESET(CLR) sequence or a power-on re-
set.
0 

–

No software ISP reset has occurred since
this bit was last cleared.

1 

–

A software ISP reset has occurred since
this bit was last cleared.

7.3

SOFTWARE RESET REGISTER 
(SWRESET)

The SWRESET register is a byte-wide, write-only register
which provides a mechanism for software to initiate a reset
into ISP mode without regard to the status of the EMPTY
bits in the flash protection word. This form of reset is only al-
lowed when all of the following conditions are true:

„

The device is in IRE or ERE mode

„

BOOTAREA is defined (has a value other than 1111b) in
the Protection Word (see Section 8.4.2 for more details).

„

ISPE is set in the flash protection word, indicating that
there is ISP code in the flash

To initiate a reset under these conditions, it is necessary to
write the value E1h to the SWRESET register, followed with-
in 127 clock cycles by the value 3Eh. The reset then follows
immediately. This sequence is called SWRESET(ISP).

Once the device has been reset into ISP mode by SWRE-
SET(ISP), any subsequent reset (other than internal or ex-
ternal power-on reset) will cause the part to reset into ISP
mode because the EMPTY bits in the Protection Word con-
tinue to be ignored.

A second set of special values written to the SWRESET reg-
ister will cause a reset out of ISP mode (whether or not the
device is currently in ISP mode). This can be used as a sim-
ple software reset. In this case, no conditions are checked.
To initiate reset out of ISP mode, write the value E1h to the
SWRESET register, followed within 127 clock cycles by the
value 0Eh. The reset then follows immediately. This se-
quence is called SWRESET(CLR). This reset also cancels
the effect of any previous SWRESET(ISP), so subsequent
resets will check the EMPTY bits to determine whether to
enter ISP mode.

The ISP reset behaves similarly to the Watchdog reset, for
example, if the flash interface is busy when reset is assert-
ed, the reset to the clock module is delayed until the flash
operations are completed.

7

6

5

4

3

2

0

ISPRST WDRST Res. DPGMBUSY PGMBUSY OENV2:0

Summary of Contents for CP3BT26























































































































































































































































































Reviews:

No comments

Related manuals for CP3BT26

PACOM Professional Series Quick Manual preview
Professional Series
Brand: PACOM Pages: 15
Stanwax Laser S4i Manual preview
S4i
Brand: Stanwax Laser Pages: 9
EK-Quantum Kinetic FLT 80 D5/DDC Body User Manual preview
Kinetic FLT 80 D5/DDC Body
Brand: EK-Quantum Pages: 16
Commell CMB-673 Installation Manual preview
CMB-673
Brand: Commell Pages: 9
IDT Digital Encoder Plus User Manual preview
Digital Encoder Plus
Brand: IDT Pages: 98
ADC HiGain H2TU-R-402 List 7A Quick Installation preview
HiGain H2TU-R-402 List 7A
Brand: ADC Pages: 7
Renesas H8S/2633 User Manual preview
H8S/2633
Brand: Renesas Pages: 28
Pressalit Care Indivo RK1010 User And Maintenance Manual preview
Indivo RK1010
Brand: Pressalit Care Pages: 31
ZALMAN CNPS11X Extreme User Manual preview
CNPS11X Extreme
Brand: ZALMAN Pages: 12
Magma ExpressBox2 EB2 User Manual preview
ExpressBox2 EB2
Brand: Magma Pages: 74
ZALMAN Fatal1ty FS-V7 User Manual preview
Fatal1ty FS-V7
Brand: ZALMAN Pages: 9
Intel E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor Datasheet preview
E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor
Brand: Intel Pages: 112
OPTO 22 PCI-AC48 User Manual preview
PCI-AC48
Brand: OPTO 22 Pages: 28
Carrier 40VMW005 Installation And Maintenance Instructions Manual preview
40VMW005
Brand: Carrier Pages: 18
Qvis 72-8P Series User Manual preview
72-8P Series
Brand: Qvis Pages: 233
ADLINK Technology AMSTX-CF Series User Manual preview
AMSTX-CF Series
Brand: ADLINK Technology Pages: 73
nox Hummer H-240CL Manual preview
Hummer H-240CL
Brand: nox Pages: 16
Terasic Cypress CapSense P0080 User Manual preview
Cypress CapSense P0080
Brand: Terasic Pages: 22

Brands by name

Popular brands

Load more brands